In an oscillating LC circuit with C = 64.0 mF, the current is given by i= (1.60) sin(2500t+ 0.680), where t is in seconds, i in amperes, and the phase constant in radians. (a) How soon after t = 0 will the current reach its maximum value? What are (b) the inductance L and (c) the total energy?

In an oscillating LC circuit with C = 64.0 mF, the current is given by i= (1.60) sin(2500t+ 0.680), where t is in seconds, i in amperes, and the phase constant in radians. (a) How soon after t = 0 will the current reach its maximum value? What are (b) the inductance L and (c) the total energy?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter14: Inductance

Section: Chapter Questions

Problem 71P: In an oscillating RLC circuit with L = 10 mH, C = 1.5 F , and R = 2.0 , how much time elapses...

See similar textbooks

Related questions

Q: An LC circuit consists of initially fully charged capacitor with a capacitance of 525 x 10-6 F and…

A: Given: Capacitance, C = 525 x 10-6 F Maximum energy stored, U = 0.65 J Resonant frequency, w =…

Q: A radar transmitter contains an LC circuit oscillating at 8.20 x 1010 Hz. (a) For a one-turn loop…

Q: The frequency of oscillation of a certain LC circuit is 300 kHz. At time t = 0, plate A of the…

Q: In an oscillating LC circuit, when 85.1% of the total energy is stored in the inductor's magnetic…

A: Energy in LC oscillation circuit:

Q: A resistor (R = 9.00 x 102 Ω), a capacitor (C 5 0.250 µF),and an inductor (L = 2.50 H) are connected…

A: Part A:

Q: At time t = 0, a 12.0 V potential difference is suddenly applied to the leads of a coil of…

Q: An LC circuit like that in the figure below consists of a 3.30-H inductor and an 834-pF capacitor…

A: Given: Value of inductor = 3.30 H Value of capacitor = 834 pF charge = 135 μC time = 5 ms

Q: In an oscillating LC circuit, L = 4.19 mH and C = 3.65 pF. At t = 0 the charge on the capacitor is…

Q: In an oscillating LC circuit in which C = 4.00 mF, the maximum potential difference across the…

Q: The frequency of oscillation of a certain LC circuit is 200 kHz.At time t = 0, plate A of the…

Q: uit, when 86.4% of the total energy is stored in the inductor’s magnetic field, (a) what multiple of…

A: In an oscillating LC circuit, when 86.4% of the total energyis stored in the inductor’s magnetic…

Q: An oscillating LC circuit consists of a 75.0 mH inductor and a 3.60 mF capacitor. If the maximum…

Q: An LC circuit consists of a 3.4-µF capacitor and a coil with a self-inductance 0.080 H and no…

A: Capacitance = C=3.4×10-6 F Inductance = L=0.08 H Initial charge = 5.4×10-6 C It is the case of LC…

Q: An LC circuit like the one in the figure below contains an 90.0 mH inductor and a 22.0 µF capacitor…

A: Given : L = 90 mH = 90 x 10-3 H C = 22 uF = 22 x 10-6 F Qo = 175 uC = 175 x 10-6 C t = 1 ms = 0.001…

Q: An LC circuit like that as shown consists of a 3.30-H inductor and an 840-pF capacitor that…

Q: A 200 Ω resistor, 1.6 H inductor, and 3.0 μF capacitor are connected in series across a 60 Hz, 120 V…

A: Given resistance(R)=200 ohms Inductance (L)=1.6 H Capacitance (C)=3.0*106 F Frequency (F)=60 Hz…

Q: North American outlets supply AC electricity with a frequencyof f = 60.0 Hz while the European…

A: a)Capacitance is given by

Q: A resistor (R = 1 Ω), inductor (L = 0.1 H) and capacitor (C = 0.1 F) are connected in series, and…

A: Given Resistor R = 1 Ω Inductor L = 0.1 H capacitor C = 0.1 F

Q: A 16.0-mH inductor is connected to a North American electrical outlet (AV = 120 V, f = 60.0 Hz).…

A: Data we have∆vrms=120v f=60.0Hz L=16.0mH=16.0×10-3H To find energy stored at time= (1/190) s

Q: What will be the total reactance of a system with a 1 μF capacitor, a 2.0 mH inductor, and a 10 kHz…

Q: At 3.7 kHz, an inductor has an impedance of 8.2j Q. What is the inductance, in uH, of the inductor?

Q: An LC circuit like the one in the figure below contains an 75.0 mH inductor and a 30.0 µF capacitor…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts (a, b,…

Q: An electromotive force E(t) = {120 (120, 0SIS 20 1 > 20 is applied to an L-R series circuit in which…

A: Disclaimer: “Since you have asked multiple question, we will solve the first question for you. If…

Q: At what frequency is the magnitude of the reactance of a 15µF capacitor equal to that of a 20-mH…

Q: What is the inductance L of a coil connected to this capacitor if the oscillation frequency of the…

Q: You are asked to build an LC circuit that oscillates at 20 kHz. In addition, the maximum current…

Q: An LC circuit consists of a 3.4-uF capacitor and a coil with a self-inductance 0.080 H and no…

A: Answer

Q: An LC circuit consists of an initially fully charged capacitor with a capacitance of 525 x 10^-6 F…

Q: In a RLC circuit connected in series, the phase angle between the voltages, V of the inductor, L and…

A: In an RLC circuit, the voltage across the inductor (VL) leads the current by 90 degrees and the…

Q: At a given time t in an LC circuit, the energy in the capacitor is 25.0% of the energy in the…

A: At t =0 , capacitor is fully charged i.e. all energy is in form of electrical energy stored in…

Q: A resistor ( R = 9.00 × 102 Ω), a capacitor (C = 0.250 µF), and an inductor (L = 2.50 H) are…

Q: In an LC circuit, the energy in the capacitor is 25.0 percent of the energy in the inductor at any…

Q: A capacitor of capacitance 158 mF and an inductor form anLC circuit that oscillates at 8.15 kHz,…

A: a) The expression foe the angular frequency of the oscillation will be,

Q: In an oscillating LC circuit in which C- 4.1 UF, the maximum potential difference across the…

Q: When an inductor is connected to a source of sinusoidally varying voltage with constant amp and…

A: Given value--- constant frequency = 60 Hz. rms value of current = 3 Amp. We have to find--- value…

Q: Consider the RLC series circuit shown in the Fig. 10 where R = 450 N, L = 89.4 mH, and C = 0.669 µF.…

Q: The frequency of oscillation of the LC circuit in the figure is 200 kHz. At time t=0 the upper…

Q: L/C. At a given time t in an LC circuit, the energy in the capacitor is 25.0% of the energy in the…

A: Solution:-

Q: In an oscillating LC circuit, L = 1.10 mH and C = 4.00 mF. The maximum charge on the capacitor is…

Q: In an LC oscillating circuit, and if we know the values of the inductance and the capacitance then…

A: The angular frequency of an LC oscillator is given by the equation; ω=1LC

Concept explainers

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention. 

Question

In an oscillating LC circuit with C = 64.0 mF, the current
is given by i= (1.60) sin(2500t+ 0.680), where t is in seconds, i in
amperes, and the phase constant in radians. (a) How soon after t = 0
will the current reach its maximum value? What are (b) the inductance
L and (c) the total energy?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Part (a)

Step 2

Step 3

Step 4

Step 5

Part (b)

Step 7

Step 8

Part (c)

Step 10

Trending now

This is a popular solution!

Step by step

Solved in 10 steps with 10 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

In an oscillating LC circuit, the maximum charge on the capacitor is qm. Determine the charge on the capacitor and the current through the inductor den energy is shared equally between the electric and magnetic fields. Express your answer in terms of qm, L, and C.
In an oscillating RLC circuit with L = 10 mH, C = 1.5 F , and R = 2.0 , how much time elapses before the amplitude of the oscillations drops to half its initial value?
In the LC circuit in Figure 33.11, the inductance is L = 19.8 mH and the capacitance is C = 19.6 mF. At some moment, UB = UE= 17.5 mJ. a. What is the maximum charge stored by the capacitor? b. What is the maximum current in the circuit? c. At t = 0, the capacitor is fully charged. Write an expression for the charge stored by the capacitor as a function of lime. d. Write an expression for the current as a function of time.
(i) When a particular inductor is connected to a source of sinusoidally varying emf with constant amplitude and a frequency of 60.0 Hz, the rms current is 3.00 A. What is the rms current if the source frequency is doubled? (a) 12.0 A (b) 6.00 A (c) 4.24 A (d) 3.00 A (e) 1.50 A (ii) Repeat part (i) assuming the load is a capacitor instead of an inductor. (iii) Repeat part (i) assuming the load is a resistor instead of an inductor.
In an oscillating LC circuit with L = 44 mH and C = 4.9 μF, the current is initially a maximum. How long will it take before the capacitor is fully charged for the first time?
A 200 Ω resistor, 1.6 H inductor, and 3.0 μF capacitor are connected in series across a 60 Hz, 120 V power supply. Calculate (a) the inductive reactance of the circuit, (b) its capacitive reactance, (c) its impedance, (d) the current through the circuit, and (e) the phase angle.
An LC circuit consists of an initially fully charged capacitor with a capacitance of 525 x 10^-6 F and an inductor. The maximum energy stored by the capacitor is 0.65 J and the resonant frequency of the circuit is 92.5 rad/s. What is the maximum current through the inductor?
After fully charging a 400 F capacitor to Qo= 8 C, an LC circuit is disconnected from its battery, when the energy stored in the capacitor is only one-fourth of its maximum value, what is the current through the inductor if L =0.03 H?
At a given time t in an LC circuit, the energy in the capacitor is 25.0% of the energy in the inductor. For this condition to occur, what fraction of a period must elapse following the time the capacitor is fully charged (at t=0)? A. 0.217 B. 0.152 C. 0.167 D. 0.176
A resistor (R = 9.00 x 102 Ω), a capacitor (C 5 0.250 µF),and an inductor (L = 2.50 H) are connected in series across a2.40 x 102 - Hz AC source for which ΔVmax = 1.40 x 102 V.Calculate (a) the impedance of the circuit, (b) the maximumcurrent delivered by the source, and (c) the phase anglebetween the current and voltage. (d) Is the current leadingor lagging the voltage?
In an oscillating LC circuit, L = 25.0 mH and C = 7.80 mF. At time t 0 the current is 9.20 mA, the charge on the capacitor is 3.80 mC, and the capacitor is charging.What are (a) the total energy in the circuit, (b) the maximum charge on the capacitor, and (c) the maximum current? (d) If the charge on the capacitor is given by q = Q cos(vt + f), what is the phase angle f? (e) Suppose the data are the same, except that the capacitor is discharging at t = 0.What then is f?
A resistor ( R = 9.00 × 102 Ω), a capacitor (C = 0.250 µF), and an inductor (L = 2.50 H) are connected in series across a 2.40 × 102-Hz AC source for which ΔV max = 1.40 × 102 V. Calculate (a) the impedance of the circuit, (b) the maximum current delivered by the source, and (c) the phase angle between the current and voltage. (d) Is the current leading or lagging the voltage?