In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and (b) The elongation

In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and (b) The elongation

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.8P: A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain...

See similar textbooks

Similar questions

A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A brass plate with a modulus of elastici ty E = 16 X 106 psi and Poisson’s ratio a = 0.34 is loaded in biaxial stress by normal stresses r and cry. (sec figure). A strain gage is bonded to the plate at an angle 4 = 350 If the stress o is 10,700 psi and the strain means used by the gageise = 390 X 106.whatisthcmax- imum in-plane shear stress (Tr, ),. and shear strain (>‘ ).? What is the maximum shear strain (y ) in the x-: plane? What is the maximum shear strain (y ).. in the y-r plane?
A circular cylindrical steel tank (see figure) contains a volatile fuel under pressure, A strain gage at point A records the longitudinal strain in the tank and transmits this information to a control room. The ultimate shear stress in the wall of the tank is 98 MPa, and a factor of safety of 2,8 is required. (a) At what value of the strain should the operators take action to reduce the pressure in the tank? (Data for the steel are modulus of elasticity E = 210 GPa and Poisson's ratio v = 0.30.) (b) What is the associated strain in the radial direction
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and(b) The elongation
In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5 x10−3 cm2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute:(a) The tensile strain and(b) The elongation
A rectangular bar is notched on two sides as shown in Fig. 5.9a. The dimensions of the bar are thickness t = 0.2 cm, D = 2 cm, d = 1.8 cm, h = 0.1 cm, and r = 0.15 cm. If an elastic load of 15 kN is applied along the axis of the bar, what is the maximum stress in the vicinity of the notches? If the yield strength of the material is 950 MPa, will the material yield near the notches under this load?
A wire with a Young’s Modulus, E, of 8.5 x 106 N/m2 and an original length of 1.5 m is under tension. If the wire length extension is 2.5 mm, calculate the stress in the wire. Give your answer in N/m2to 2 decimal places. (show all work)
A sample of silicone breast implant, polydimethylsiloxane (PDMS), is placed under unconfined compression. The magnitudes of the resulting longitudinal and transverse strains have been measured to be 2.7 and 1.341, respectively. The young's modulus of the implant is 500 kPa. Calculate the shear and bulk moduli.
A rectangular steel block is 300mm in the x direction, 200mm in the y direction and 150mm in the z direction. The block is subjected to a triaxial loading consisting of three uniformly distributed forces as follows: 250kN tension in the x direction, 320kN compression in the y direction and 180kN tension in the z direction. For steel, v=0.30 and E=200,000MPa. Determine the total strain in the x direction due to the forces applied in the three directions.
The error in a measurement due to strain when using a tape measure depends on the material that it is made of. For a tape with a cross section of 10 mm by 0.7 mm, calculate how much error is introduced in inches into the measurement at a 300 ft length if the tape is pulled with 80 N and if the tape is made of: a) mild steel (E = 30 x 10^6 psi), b) polycrystalline aluminum (E = 10 x 10^6 psi) c) fiberglass composite (E = 3.5 x 10^6 psi in the long direction)
1. A solid piece of metal of volume 10,000 mm3 is compressed by a pressure of 70 MPa. Determine the bulk modulus given that the Young’s modulus E is 214 Gpa and the Poisson’s ratio is 0.33. Also determine the change in the volume.2. Starting from the first principles derive the relation between Young’s modulus (E), shear modulus (G) and Poisson’s ratio (υ)
(30%) A circular aluminum tube subjected to T pure torsion by torques T has an outer radius r2 equal to 2 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 500x10-6 rad, what is the shear strain y1 at the inner surface? (b) If the maximum allowable rate of twist (0) is 0.15°/m and the maximum shear strain is to be kept at 500x10-6 rad by adjusting the torque T, what is the minimum required outer radius (r2 )min?