A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus forming a square opening in the plate. a. If the allowable compressive stress in the plate is 24 ksi, what is the maximum punching force, in pounds, that this die can exert on the plate? b. If the aluminum has an ultimate shear strength of 6500 psi, find the maximum thickness t, in inches, through which a hole may be punched. Write to three decimal places. Punch force Steel punch Aluminum plate, Die Punched piece

A 1.25 in.-square steel punch is to push through an aluminum plate that is supported on a die, thus forming a square opening in the plate. a. If the allowable compressive stress in the plate is 24 ksi, what is the maximum punching force, in pounds, that this die can exert on the plate? b. If the aluminum has an ultimate shear strength of 6500 psi, find the maximum thickness t, in inches, through which a hole may be punched. Write to three decimal places. Punch force Steel punch Aluminum plate, Die Punched piece

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A single bolt is used to lap joint two steel bars together. Tensile force on the bar is 20,000 N. Determine the diameter of the bolt required if the allowable shearing stress is 70 MPa?
A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm diameter steel bolts must be used on a 200-mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
Mechanics Lesson The 6 kN force is in the vertical direction, while the P=7.5 kN force is in the z direction.Since the safe shear stress is 60 MPa, determine the smallest allowable diameter of the AD shaft.
The maximum torsional shear stress of a shaft with diameter D can be found at what distance from the center of the shaft?
If the ultimate shear strength of a steel plate is 42,000psi. What is the force necessary to puncha 0.75in diameter hole in a 0.625in thick plate
Find the max shear stress in given data of two circular shafts (S) AND (H)
A wire with circular base of radius 3 mm was subjected to tensile stress of 13.5 N. If half the amount of stress is to be applied to a wire with square base of 1.86 mm width, what must have been the force (in Newton) applied to this new wire?
A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the shaft material is 56 N/mm2. Determine the diameter of the shaft?
Figure shows that a hole must be drilled in a plate with a shear strength of 40 ksi. Compressive stress in the punch is limited to 50 ksi. If the plate is 0.25 in. thick, determine the diameter of the smallest hole. that can be drilled. The figure is in the attached image.
Two plates are held together by 4, 28 mm diameter bolts. If a 25 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa?
Three plates are held together by 2, 11 mm diameter bolts. If a 16 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa?
An aluminum thin‐walled tube of hollow rectangular cross‐section, Figure 1,is subjected to a torque of magnitude, T = 15360 N.m. If the tube lengthis, L = 1 m , and the shear modulus of aluminum is, G = 28 GPa.1. Determine the total angle of twist of the one‐meter long tube.2. Determine the shear stresses on the walls of the tube cross‐section.Where does the maximum shear stress occur?