In convection heat transfer, what happens to the heat transfer coefficient if the viscosity of the fluid decreases? Select the correct response: The heat transfer coefficient remains constant The heat transfer coefficient also increases The heat transfer coefficient partially increases then decreases The heat transfer coefficient will decreases

In convection heat transfer, what happens to the heat transfer coefficient if the viscosity of the fluid decreases? Select the correct response: The heat transfer coefficient remains constant The heat transfer coefficient also increases The heat transfer coefficient partially increases then decreases The heat transfer coefficient will decreases

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.22P

See similar textbooks

Similar questions

in convection heat transfer, what happen to the heat transfer coefficient if the viscosity of the fluid decrease?
Water flows at a rate of 0.8 kg /s in a 2.5 -cm diameter tube whose surface is maintained at a constant temperature of 90°C. If water must be heated from 35°C to 40°C, what is the value of the temperature on which you will base the value of the thermal conductivity that will be used to compute for the convection heat transfer coefficient? Express in Celsus.
A water tank is completely filled with liquid water at 20ºC. The tank material is such that it can withstand tension caused by a volume expansion of 0.75 percent. Determine the maximum temperature rise allowed without jeopardizing safety. For simplicity, assume the volume expansion coefficient β at 313 K to be 0.377 × 10–3 K–1. The maximum temperature rise allowed in the tank is ______ ºC.
A long 8-cm diameter vertical steam pipe whose external surface temperature is 90oC passes through some open area that is not protected against the wind blows. Determine the rate of heat loss from the pipe per unit length when the air is at 1 atm, 7oC and the wind is blowing across the pipe at a velocity of 50 km/h. From Table A-1: Thermal conductivity, k = 0.0275 W/m oC , viscosity, v = 1.77 x 10-5 m2/s Prandtl no. Pr = 0.71
An coconut oil (considered as viscous fluid) must be pumped between two buildings in an agro-industrial plant through an AISI 304 stainless steel pipe spread on the ground that has an outside diameter of 22 cm and 110 m long. To facilitate pumping, the liquid will be heated to 40 ° C in order to reduce its viscosity. The oil flow rate will be 20 Kg / s and the specific heat will be 1300 J / Kg K. Determine the temperature drop that the liquid will experience along the pipeline under the following operating conditions:Ambient air temperature = 10 ° CWind speed = 14 m / sPipe surface temperature = 37 ° C
Relationship between fluid flow and convection heat transfer
Which of the three transport processes (momentum transfer, heat transfer, and mass transfer) is regarded the resistance? Choose 1. Temperature, pressure, viscosity, or length of transport
A 6cm diameter shaft rotates at 3000rpm in a 20cm long bearing with a uniform clearance of 0.2mm. At steady operating conditions, both the bearing and shaft in the vicinity of the oil gap are 50°C. The thermal conductivity and the viscosity of the lubricating oil are k=0.17 W/m-K and µ= 0.05 N-s/m2, respectively. By simplifying and solving the differential continuity, momentum and energy equation, determine the maximum temperature of oil. (Hint: Couette flow)
A 6 cm diameter shaft rotates at 3000 rpm in a 20 cm long bearing with a uniform play of 0.2 mm. Under stable operating conditions, both the bearing and the shaft in the vicinity of the oil gap are at 50 ° C, and the viscosity and thermal conductivity of the lubricating oil are 0.05 Ns / m 2 and 0.17 W / mK. Simplifying and solving the equations for continuity, momentum, and energy, determine (a) the maximum oil temperature, (b) the rates of heat transfer to the bearing and shaft, and (c) the mechanical power wasted by viscous dissipation in Oil. Answers: (a) 53.3 ° C, (b) 419 W, (c) 838 W
Consider the flow of oil at 20°C in a 30-cm-diameter pipeline at an average velocity of 2 m/s. A 200-m-long section of the horizontal pipeline passes through icy waters of a lake at 0°C. Measurements indicate that the surface temperature of the pipe is very nearly 0°C. Disregarding the thermal resistance of the pipe material, determine (a) the temperature of the oil when the pipe leaves the lake, (b) the rate of heat transfer from the oil, and (c) the pumping power required to overcome the pressure losses and to maintain the flow of the oil in the pipe.
During air cooling of oranges, grapefruit, andtangelos, the heat transfer coefficient for combined convection,radiation, and evaporation for air velocities of0.11 < V < 0.33 m/s is determined experimentally and isexpressed as h = 5.05 kair Re1/3/D, where the diameter Dis the characteristic length. Oranges are cooled by refrigeratedair at 5°C and 1 atm at a velocity of 0.3 m/s. Determine(a) the initial rate of heat transfer from a 7-cm-diameterorange initially at 15°C with a thermal conductivity of0.50 W/m·K, (b) the value of the initial temperature gradientinside the orange at the surface, and (c) the value of theNusselt number.
air is flowing inside of a pipe with radius=0.4 meters at a mass velocity of 29.4 kg/s*m2 at 322 K, with the walls of the pipe at 300 K. At the conditions of the experiment, the viscosity of air is 1.984 x 10-5 Pa*s, the density of air is 1.22 kg/m3, the heat capacity is 1 kJ/kg*K, and the thermal conductivity is 0.025 W/m*K. Determine the rate of heat loss by air per meter of duct.