PLEASE ANSWER WITH DETAILED STEPS AND EXPLANATION. THANKS ? CONVECTION10Nu - 0.023 Re*Pr10Figure 2-6 Typical datacorrelation for forcedconvection in smooth tubes,1010turbulent flow.101010Reynolds number Using the relationship shown on Fig. 2-6 for heat transfer when a fluidflows inside a tube, what is the percentage increase or decrease in theconvection heat-transfer coefficient hc if the viscosity of the fluid isdecreased 10 percent? Ans. 4.3% increase

Answered: Image /qna-images/answer/dbe14685-5048-423a-83ea-33f7ca666932.jpg

Using the relationship shown on Fig. 2-6 for heat transfer when a fluid flows inside a tube, what is the percentage increase or decrease in the convection heat-transfer coefficient hc if the viscosity of the fluid is decreased 10 percent? Ans. 4.3% increase

Using the relationship shown on Fig. 2-6 for heat transfer when a fluid flows inside a tube, what is the percentage increase or decrease in the convection heat-transfer coefficient hc if the viscosity of the fluid is decreased 10 percent? Ans. 4.3% increase

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Related questions

Q: -Explain in details how we can use Pitot tube in order to measure the follow of the fluids using…

Q: The ratio of the mass of actual dry steam to the mass of same qantity of wet steam is called *…

Q: Oil with density 905 kg/m^3 and viscosity 2.33 kg/m.s flows in a 430 meter long 42-cm-diameter…

Q: water is flowing in a pipe with raduis of 30 cm at a velocity of 7 m/s at the temperature of…

Q: 1- Consider single-phase fluid flow in a 1-D horizontal reservoir. The reservoir is discretized…

Q: Fluid with a density of 736 kg/m² flows inside a 6.0 cm diameter tube at a velocity of 1.3 m/s. The…

Q: a pipe of diameter 60 mm is subjected to an oil flow at rate of 343.5 kg/s. the mass density and…

A: Pressure gradient in the pipe is 1080 kPa/m.

Q: A liquid is being pumped through a pipe whose diameter is 15mm. At the operating temperature and…

Q: A liquid flows through a 200 m long pipe with a rectangular cross section with 0.6mX0.3m dimensions.…

A: Length of the pipe, L=200m Cross-sectional area of rectangular section, A=0.6m*0.3m=0.18m2 The…

Q: i need the answer quickly

Q: What happens to the heat transfer coefficient in convection heat transfer if the viscosity of the…

A: Viscosity: The resistance to flow of any fluid is known as viscosity. The viscosity of any fluid is…

Q: A Pitot-static probe is mounted in a 2.5-cm-inner diameter pipe at a location where the local…

A: Diameter of pipe is (d) = 2.5 cm = 2.5*0.01 (m)…

Q: he fluid is oil with a kinematic viscosity 6f 0.000217 m²/s and the spacing pen plates is 40 mm. The…

Q: e water side to be 0.002 m² degree/W per tube and on the shell side and thermal resistance of the…

A: n=100dinner=25mmthickness : t=2mmdouter=29mmm.c=28kg/stc1=25°Ctc2=75°Cth1=th2=50°Cheat transfer…

Q: A weir is used to: * O measure the flow rate of open-flowing liquids control the flow rate of an…

A: A weir is used to measure flow rate of open flow liquid Option a is correct

Q: For internal flow with fully developed flow condition The velocity profile ....................…

A: In the entry region during internal flow, velocity profile and thermal profile change in the…

Q: A pump is used to raise oil with density= 940 kg/ m, from a lower tank to a higher tank through tube…

A: Given data: P = 940 kg/m3 , A = 40cm by 50cm , L = 450mV = 0.00001 m2/s , Q = 0.2 m3/s , r/d=D1/D2 =…

Q: 3) The clutch system shown in the figure is used to transmit torque through a 2 mm thick oil film…

Q: A liquid is being pumped through a pipe whose diameter is 15mm. At the operating temperature and…

Q: A 15 m building use cast iron pipes in their piping system. The water tank located on the top of the…

Q: An coconut oil (considered as viscous fluid) must be pumped between two buildings in an…

A: Given data: The oil flow rate is m = 20 kg/s. The liquid will be heated to temperature of To = 40…

Q: E OF PIPE IN

A: Insulation is a term used to describe a material or a combination of materials that slows the…

Q: There is a hot water source in New Delhi.Our plan is to use this heat source for heating and hot…

A: The two organic fluids are - R600 - It is non-toxic, non-flammable and has a critical temperature…

Q: In the design of small-scale bioprocess plant, a shear sensitive Newtonian liquid of density 1100…

A: As per the question mentioned, it is a shear sensitive Newtonian liquid , it mean it is case of…

Q: Air is an example of O Dilatant fluid O Non Newtonian fluid O Newtonian fluid O Bingam plastic fluid

Q: Engine oil enters the 5 mm diameter pipe at 120°C. The pipe surface temperature is kept at 40°C and…

Q: Determine the inside diameter of a tube that could be used in a high temperature, short time…

Q: ition Reynolds number for flow in a circular pipe is Re=2300. For flow through a 5-cm-diameter pipe,…

A: Givenreynold number Re=2300diameter of pipe d=5cm=0.05mtemperature T=20oCthe Kinematic Viscosity of…

Q: Figure 3 shows a large drinking water bottle equipped with a hose and a valve. One end of a 7 mm…

Q: A boiling-water nuclear reactor vessel comprises a cylinder of length 20 m and diameter 5 m with…

A: Given that, Length of cylinder, L=20 m,Diameter of hemispherical end, d=5 m,Power generated, Q˙=1800…

Q: a) In the transmission system of an automobile, the rotating shaft powered by the engine is…

A: Given: The film thickness, t = 4 mm = 0.004 m The viscosity of oil = 0.5 Pa.s The diameter of disc,…

Q: Q1 a) What is the physical significance of Reynolds number? Write down 5 (five) factors that…

A: Given: The inlet temperature of water, Ti = 10°C The outlet temperature of water, To = 80°C The tube…

Q: What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The…

Q: If the mass velocity for water at 80°F flowing through a 1 in. diameter tube is 30,000 slug/hr-ft?.…

A: Given Mass velocity, mv = 30000 slug/hr.ft2 Diameter, d = 1 in = 0.0833 ft…

Q: The area between two infinite flat parallel sheets which are placed 10mm away from each other is…

A: Given data: - The distance between plate and sheet is y = 4 mm. The distance between sheets is h =…

Q: Water at 303 K is flowing at the rate of 6.3x10-4 m3/s in a pipe having an inside diameter (ID) of…

Q: The clutch system shown in the figure is used to transmit torque through a 2-mm-thick oil film with…

A: Given DataN1=1200rpmN2=1125rpmD=0.3mμ=0.38N-s/m2

Q: An oil is being pumped inside a 10.0 mm diameter pipe. The oil’s density is 855 kg/m3 and its…

Q: can you make explain this question base on your own words. "In understanding the behavior of fluids,…

Q: Water flows inside the tube 45mm diameter and 3.5 meters long at a velocity 1m/s. Determine the heat…

Q: Are these equations valid only for ideal fluids or they are also valid for non-ideal fluids? Explain…

Q: Thick fluids such as asphalt and waxes am the pipes in which they flow are often heated in order to…

Q: temperature difference between the čentre and the surface of the steel ball is

A: Given data; diameter(d)=12mm=0.012mT=1000Kt=300kCoeffiecient of heat tranfer=5 W/m2KThermal…

Q: Consider a fluid with a Prandtl number of 7 flowing through a smooth circular tube. Using the…

A: Now, consider the value of Reynold’s Number as 3500, the Nusselt numbers are calculated by given…

Q: Fluid with a density of 602 kg/m³ flows inside a 3.3 cm diameter tube at a velocity of 1.7 m/s. The…

A: The convection heat transfer coefficient: h = 3755 W/m2•K

Q: Give me your thoughts in the inverse proportionality between bulk velocity of a liquid flowing…

A: Fluid properties can change with velocity. Friction factor in a fluid indicates the head loss that…

Q: A Figure illustrates the tube-flow system. The heat transfer under developed flow conditions when…

Concept explainers

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.

Question

PLEASE ANSWER WITH DETAILED STEPS AND EXPLANATION. THANKS ?

CONVECTION
10
Nu - 0.023 Re*Pr
10
Figure 2-6 Typical data
correlation for forced
convection in smooth tubes,
10
10
turbulent flow.
10
10
10
Reynolds number

Using the relationship shown on Fig. 2-6 for heat transfer when a fluid
flows inside a tube, what is the percentage increase or decrease in the
convection heat-transfer coefficient hc if the viscosity of the fluid is
decreased 10 percent? Ans. 4.3% increase

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

water is flowing in a pipe with raduis of 30 cm at a velocity of 7 m/s at the temperature of viscosity of water is 614 pa.s. what is the reynolds number for this
An oil is being pumped inside a 10.0 mm diameter pipe. The oil’s density is 855 kg/m3 and its viscosity is 2.1×10-2Pa·s. It is required that the flow remain in the laminar regime and thus the Reynolds number cannot exceed 2100.What is the maximum velocity in the pipe?
What is the Reynolds number of a fluid flowing in a tube with an inside diameter of 1 inches? The viscocity is 1.353 x 10^ -5 lb/ft-s and the mass flow rate is 79 lb/h.Correct Answer: 24,780.96 ± 1%
A Pitot-static probe is mounted in a 2.5-cm-inner diameter pipe at a location where the local velocity is approximately equal to the average velocity. The oil in the pipe has density ? = 860 kg/m3 and viscosity ? = 0.0103 kg/m⋅s. The pressure difference is measured to be 95.8 Pa. Calculate the volume ﬂow rate through the pipe in cubic meters per second.
Engine oil enters the 5 mm diameter pipe at 120°C. The pipe surface temperature is kept at 40°C and the Re number is about 1000. Calculate the heat lost by the fluid for a 30 cm long pipe? Engine oilYou can get its specs at 390K.
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
This is a resubmission question. I need assistance in solving this experiment. fluid flowing in the pipe is AIR at 15degrees celsius.
plzzz i neeed the answer right nowwww What is the air pressure (kpa) in a car tier? The pipe pressure is measured to be 20 kpa. For layers of oils, given that S1=1.0, S2=0.8, and S3=0.17.
Describe the process of internal flow convection heat transfer in an annular tubeconcentric and draw
Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance of 2000 m. Ifthe line is isothermal at 323.15 K and the pressure at the entry point is 750 ×103 Pa and at the exit point is 430×103 Pa, what diameter should the pipe has to ensure that the CO2 will be delivered to the end point with the pressure drop experienced. The viscosity of CO2 at 323.15 K is 1.45×10-5kg/m.s. One trial is sufficient given you tell us how you will proceed to achieve an accurate diameter estimate. Hint: for your initial guess, use D in the range of 0.01-0.02 m.
The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? = 0.38 N⋅s/m2 between two identical 30-cm-diameter disks. When the driving shaft rotates at a speed of 1200 rpm, the driven shaft is observed to rotate at 1125 rpm. Using appropriate software, investigate the effect of oil film thickness on the torque transmitted. Let the film thickness vary from 0.1 mm to 10 mm. Plot your results, and state your conclusions.
A liquid flows through a 200 m long pipe with a rectangular cross section with 0.6mX0.3mdimensions. The dynamic viscosity of the liquid is 2.33 kg/ms and the density is 894 kg/m3. Ifthe average velocity of the fluid is 0.8m/s what is the necessary pumping power in kW tomaintain the flow of the liquid?