In (Figure 1), take that w = 2.5 kN/m.Figure3 mWo1.5 m1 of 1Part AReplace the distributed loading with an equivalent resultant force.Express your answer to three significant figures and include the appropriate units.SubmitPart BμAValueSubmitRequest AnswerValueSpecify its location on the beam measured from point O.Express your answer to three significant figures and include the appropriate units.μAUnitsRequest Answer?Units?

Answered: Image /qna-images/answer/17377b2c-ebb8-4165-b06c-a70b2c8107c9.jpg

In (Eigure 1), take that uy = 2.5 kN/m. igure 3 m- Wo 1.5 m 1 of 1 > ▼ Part A Replace the distributed loading with an equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR- Submit Part B Submit НА Value Request Answer Specify its location on the beam measured from point O. Express your answer to three significant figures and include the appropriate units. HA Value Units Request Answer Units ? ?

In (Eigure 1), take that uy = 2.5 kN/m. igure 3 m- Wo 1.5 m 1 of 1 > ▼ Part A Replace the distributed loading with an equivalent resultant force. Express your answer to three significant figures and include the appropriate units. FR- Submit Part B Submit НА Value Request Answer Specify its location on the beam measured from point O. Express your answer to three significant figures and include the appropriate units. HA Value Units Request Answer Units ? ?

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter7: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 7.2P: A planned flexible load area (see Figure P7.2) is to be 3 m × 4.6 m and carries a uniformly...

See similar textbooks

Similar questions

A pull of 6,500 lb is applied to a steel rod which has an ultimate stressof 65,000 psi. Determine the steel rod diameter if the factor of safetyis 5.A. 0.998 inch C. 0.798 inchB. 0.598 inch D. 0.398 inch
In the trapezoidal load shown, if h1 = 4 kN/m, and y = 3 kN/m. What is the value of h2?
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of thewhole structure which is SN lbs per ft complete solution and drawing. if u can please add some explanation thankyou FN = 49 MN = 101 SN = 94
a. What is the magnitude of the roller reaction in lb? b. What is the equivalent resultant force of the distributed loading in lb?
A bearing pad is a device which is used to support a bridge or other heavystructure in a way that permits the load to shift slightly in a horizontal directionrelative to the ground or foundation. If a horizontal force af 528 kN is applied tothe top surface of the bearing pad, and that a = 700 mm, b = 550 mm, h = 75m and the modulus of elasticity G = 1.25 MPa. Determine the following: a. The average shear stress on the bearing pad.b. The horizontal displacemant of tne bearing pad. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
Construct the shear -force diagram and identify the largest negative shear force. Assume a = 3.1 ft, b = 6.2 ft, c= 12.4 ft, W= 1200 1b/ft. and Pa 1200 1b,
Consider the beam shown in (Figure 1). Suppose that M = 9 kip⋅ft, P = 6 kip, w = 1.2 kip/ft, and point D is located just to the left of the 6-kip load. Follow the sign convention. Part A Part complete Determine the internal normal force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part B Determine the internal shear force at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part C Determine the internal moment at section passing through point D. Express your answer to three significant figures and include the appropriate units. Part D Part complete Determine the internal normal force at section passing through point E. Express your answer to three significant figures and include the appropriate units. Part E Determine the internal shear force at section passing through point E. Express your answer to…
A rectangular “Apitong” beam 50mm x 300mm is used as a simply supported beam 3.2m long. Determine the largest uniformly distributed load, which can be, applied over the central half of the beam if the flexural stress is limited to go 12MPa?
(c) Figure Q2(c) shows a homogenous 1.2 m wide and 3 m long rectangular gate is held in place by a horizontal flexible cable. Water acts against the gate, which is hinged at point A. Calculate the magnitude, FR and location of the resultant force, yR.
Three forces are applied in a system whose resultant is zero, one of the force is unknown: F1 (70lbs, 45deg NE), F2 (80 lbs, 65deg SE). Compute the horizontal force (lbs) of the unknown force.
Compute σz in kPa at point A due to the two-line loads shown in figure.