(Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the pressures at sections (1) and (2) are 262 kPa and 116 kPa, respectively. Determine the diameter of the pipe at section (2), D₂, if the velocity at section 1 is 21 m/s and viscous effects are negligible. P2 = 116 kPa m P₁ =262 kPa D₁=0.11 m 52 m 17

(Bernoulli/continuity) Water flows steadily through the pipe shown in the figure below such that the pressures at sections (1) and (2) are 262 kPa and 116 kPa, respectively. Determine the diameter of the pipe at section (2), D₂, if the velocity at section 1 is 21 m/s and viscous effects are negligible. P2 = 116 kPa m P₁ =262 kPa D₁=0.11 m 52 m 17

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water at 10°C has a kinematic viscosity of 1.30 X 10-6 m2/s flows at the rate of 896.61 L/min from the reservoir and through the pipe shown in the Fig. below. Compute the pressure at point B, considering the energy loss due to friction, but neglecting other losses. Also, use pipe roughness of 1.50 X 10-6 m. Hint: Use the appropriate formula to determine the friction factor, f to 4 decimal places (flow type dependant); g = 9.81 and round off to 3 decimal places for all other step calculations leading to the final answer including the final answer.
A pipe AB carries water and tapers uniformly from a diameter of 0.1 m at A to 0.2 m at B over a length of 2 m. Pressure gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 100 kPa) Determine the flow, in m^3/s through the pipe at C neglecting all losses. (1 bar = 100 kPa). (Please round-off final answer to four decimal places) Determine the pressure in bars, recorded at C neglecting all losses. (Please round-off final answer to 2 decimal places)
Calculate the diameter of vertical pipe needed for flow of liquid at R = 1800 when the pressure remains constant. v = 1.5 um?/s.
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
6. Compute the lost head in a 150-mm pipe if it is necessary to maintain a pressure of 231 kPa at a point upstream and 1.83 m below where the pipe discharges water into the atmosphere at the rate of 0.0556 m /s. indicate free body diagram
Hydraulics ProblemAn open horizontal tank 1.5m high 2m wide and 5m long is full of oil with a specific gravity of 0.9. It is accelerated in the direction parallel to the longer length at 2.3 m/s2 a. What is the force acting on the wall of the tank with the shortest depth in KN? b. If the acceleration is increased by 0.88 m/s2. Determine the volume of oil that spilled out the tank?Note: Draw free-body diagram and used 4 decimal places
The pressures at the ends of 605m long horizontal pipe flow are 350 kPa and 270 kPa. The pressure at the point between the ends is 300 kPa. The pipe is 305mm in diameter and n=0.018. Find the total headloss, amount of flow, and the slope of the egl.
A sluice gate flows into a horizontal channel as shown in the figure. Determine the flow through the gate per meter width when y=1.0m and d1=6m. Assume that the pressure distributions at section 1 and 2 to be atmospheric and neglect losses in the channel. Use coefficient of contraction Cc= .85 and coefficient of velocity is Cv=.95.
Water flows through the horizontal branching pipe shown below at a steady rate of 10 ft3 /s. If viscous effects are negligible, determine the water speed at section (2), the pressure at section (3) and the flow rate at section (4)
With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized chamber A is poured into the atmosphere with a 40 cm fixed diameter BCDEF pipe. Since zB=29, zC=10, zD=28.5, zE=5 and zF=28 meters according to the comparison plane;a) Calculate the flow of the system.b) Draw the relative load (energy) and piezometer lines of the system.c) Determine where the greatest pressure will be observed throughout the system and calculate its relative value.
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3