In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless. The shaft rotates with a uniform angular velocity. The known belt pulls are indicated and the three pulleys are rigidly keyed to the shaft. If the working stress in shear is 64 MPa, determine the necessary diameter of a solid circular shaft. 3 kN 1 kN 250 mm B -500 mm- 1 kN 1.25 kN 350 mm

In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless. The shaft rotates with a uniform angular velocity. The known belt pulls are indicated and the three pulleys are rigidly keyed to the shaft. If the working stress in shear is 64 MPa, determine the necessary diameter of a solid circular shaft. 3 kN 1 kN 250 mm B -500 mm- 1 kN 1.25 kN 350 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine support reaction. Given a=5 m b=10 m P=30 KN
Determine support reaction at B . Given P=100 Kn L=10 m
Determine the maximum horsepower a solid steel shaft 2.25in in diameter can transmit at 250rpm if the working stress in shear is 11,000lb/sq.in.
THE ANSWER MUST BE IN FOUR DECIMAL PLACES the steef shaft shown in figure rotates at 4Hz with 35 KW taken off at A, 20 kW removed at B and 55 kW applied at C. Using G=83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C
A 5-m STEEL SHAFT ROTATING AT 2Hz HAS 70 KW APPLIED AT GEAR THAT IS 2m FROM THE LEFT END WHERE 20 KW ARE REMOVED.AT THE RIGHT END, 30KW ARE REMOVED AND ANOTHER 20 KW LEAVES THE SHAFT AT 1.5m FROM THE RIGHT END. (A) FIND THE UNIFORM SHAFT DIAMETER SO THAT THE SHEARING STRESS WILL NOT EXCEED 60 MPa. (B) IF A UNIFORM SHAFT DIAMETER OF 100mm IS SPECIFIED, DETERMINE THE ANGLE BY WHICH ONE OF THE SHAFTS LAGS BEHIND THE OTHER END. USE G = 83 GPa.
If the coefficient of static friction at contact points A and B is μs = 0.3, determine the maximum force P that can be applied without causing the 100-kg spool to move.
There is a (45/10) kg slider ring is going down from the rest position A and slides in frictionless guide pipe as seen in the picture below. (h= 5+5 m.) For this situation, please determine the velocity as the slider ring at B and calculate the maximum compression of the spring in millimeters.
The skid-steer loader has a mass of 1.18 Mg, and in the position shown the center of mass is at G1. If there is a 300-kg stone in the bucket, with center of mass at G2, determine the reactions of each pair of wheels A and B on the ground and the force in the hydraulic cylinder CD and at the pin E. There is a similar linkage on each side of the loader.
As shown in Figer the rectangular gate AB is hinged at A ,its wide (2m) and weighs (10 kn). Determine the minimum gage pressure at (G) required for opening the gate.
Determine the Force Frequired to hold the bar AB in a horizontal position on the smooth inclines shown in figure below. Also determine the reactions at A and B 1.2m, 4.2m, 0.6m A 60 degrees and 45 degrees B 90N
The cylinder weighs 10 lb and is held in equilibrium by the belt and wall. If slipping does not occur at the wall, determine the minimum vertical force P which must be applied to the belt for equilibrium. The coefficient of staticfriction between the belt and the cylinder is μs = 0.25.
The 600-Ib, 20ft-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal. The gate is to be opened from its lower edge by applying a normal force P at its center. A. Determine the magnitude if the hydrostatic force acting on the gate using the hydrostatic panel equations. Express your answer in kips.