Course : Electronics II 4. In Figure 4, the input signal results in a base current of 10 mA peak and choose anyvalue of Rc within these limits: 10 O S RCS 20 N.a) Find input power, output power, efficiency.b) Determine the maximum input power, maximum output power andmaximum efficiency.c) Plot the DC Load Line.+Vcc (18 V)Ra1.5 k2100 µuFFigure 4

Answered: Image /qna-images/answer/630e3a84-a0e0-42f9-aee4-0dc32d66568f.jpg

In Figure 4, the input signal results in a base current of 10 mA peak and choose any value of Rc within these limits: 10 N S RCS 20 N. a) Find input power, output power, efficiency. b) Determine the maximum input power, maximum output power and maximum efficiency. c) Plot the DC Load Line.

In Figure 4, the input signal results in a base current of 10 mA peak and choose any value of Rc within these limits: 10 N S RCS 20 N. a) Find input power, output power, efficiency. b) Determine the maximum input power, maximum output power and maximum efficiency. c) Plot the DC Load Line.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit given in the figure, VT = 25mV, | VBE | = 0.7V, R1 = 1402.66Kohm, R2 = 32.67Kohm, R3 = 2.91Kohm, R4 = 1.25Kohm, VCC = 10.00V, VEE = -5.00V, VA = 25.00V, Since Beta = 208.00, Rs = 28.63ohm, Ry = 13.62Kohm, calculate the IC current, Ri, R0 and the voltage gain according to the Source (V0 / V1) by full analysis.
Power Electronics. In the Buck-Boost DC-DC converter circuit:Welding voltage [40-80]VSwitching frequency (f) 25khzVoltage between load terminals 55VCapacitance value 470uFLoad current value [10-25]A Under these conditions, which is the lowest ripple (delta IL) amount of the current passing through the coil (L) in Amps for the lowest L inductance value that can keep the DC-DC converter in a continuous current state? A) 23.9803B) 118.75C) 84.3750D) 47.5E) 59.9507F) 33.75
amplifier (boost) DC-DA converter circuit, given below; 1- Source voltage (E) value: In the voltage range of [A B] (Volts) 2- Switching frequency (f) value: M kHz 3- Voltage between load terminals (Vload) F (volt) 4- Capacity value is 470 (microF) 5- Pload>= H(watts) consumed per load In which case below do you see the lowest L inductance value in microH that can keep the DC-DC converter in a continuous current state under the conditions? A=25 VOLT B=40 VOLT M= 25kHz F = 55 VOLT H=15 Watts a) 454.5475 b) 382,045 c) 263.62 d) 128.5 e) 581.81
In the Buck - Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: in the voltage range of [AB] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (UF) 5) Load current lload) value: [KS] (Amps) current range The lowest Linductance value that can keep the DC-DC converter in continuous current condition under The lowest ripple (AIL) amount of the current passing through the coil (L) is given below in Amps. Which option do you see? A = 40 Volts B = 80 Volts M = 25kHz F = 55 Volts K = 10 Amps S = 25 Amps
Determine the value that the unknown emf (E) must have so that the potential V12 = 9v
According to the circuit given in the figure, VT=25mV, |VBE|=0.7V, R1=1487.51Kohm, R2= 7.42Kohm, R3= 6.71Kohm , R4= 2.87Kohm, VCC= 13.00V, VEE= 1.00V , VA=28.21V , Beta= 120.00 , Rs= 36.18ohm, Ry= 15.61Kohm Calculate the IC current, Ri, R0 and voltage gain(V0/V1) according to the source by performing a complete analysis. When performing your operations, 2 steps will be taken after the point. choose the closest one from the stylish ones according to the +/-10% margin of error. There is only 1 correct answer to the question.
In the Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: In the voltage range [ AB ] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (uF) 5) Pload 2 H (Watts) consumed per load The lowest L inductance value that can keep the DC-DC converter in continuous current condition under Which option do you see below as pH ? A = 10 Volts B = 19 Volts M = 23kHz F = 26 Volts H = 8 Watts
It is known that Vi = 62 mV IDSS = 12 mA, VP = -4 V, VGSQ = -2.5 V, RD = 3.2 kΩ and RS = 1.2 kΩ in the circuit in the figure. Accordingly, what is the value of the output voltage of the circuit (V0)? NOTE: The FET output impedance (rd) will not be taken into account in the calculations.
A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.A dc power supply is to be developed by employing an ac to dc converter as a power processing converter for 180 watts highly inductive load. The rms value of the input ac phase voltage is 230 V at 50 Hz frequency. Select a suitable rectifier circuit having improved ripple factor and power factor for this application. The output dc voltage is assumed to be (245). The output dc voltage should be multiplied with ‘0.5’ if it exceeds the 200 V.
In the circuit above, if V1 = + 28V, R = 17,612, RL = 14,3 and the zener voltage is 8,0, what is the peak point of the voltage falling on the resistor R in the negative alternans of V1?
(a) What is the output current IO in the circuitshown if −VEE = −10 V andR = 20 ohm? Assume that the MOSFET is saturated.(b) What is the minimum voltage VDDneeded to saturate the MOSFET if VTN = 2.5 Vand K'n = 0.25 A/V2. (c) What must be the powerdissipation ratings of resistor R and the FET.
design a battery charger for safe operation in a damp garage environment to use for charging your 12 VDC car battery. Design specifications include: (a) Input is a 110rms VAC. (VP=110x ) at 60 Hz from a three wire service that meets the National Electrical Code. (b) Output is a nominal 12 volts VDC at the cathode of the diode. (c) Specify a resistor, R, to limit the maximum battery charging current to 10 amperes into the 12 volt car battery assuming the battery is completely dead (0 volts) when you first connect the charger. (d) There is no ripple voltage design specification. Explain why this is unnecessary in this application. (e) The battery charger case is metal. (f) Assume a diode with VF = 0.7 V (g) The fuse in the primary circuit is to protect the power supply from a short-circuit at the battery terminals either from total battery failure or accidentally short circuiting the charging cable to ground…