Answered: In open-die forging, a disc of diameter…

In open-die forging, a disc of diameter 200 mm and height 60 mm is compressed without any barreling effect. The final diameter of the disc is 400 mm calculate the true strain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: When deforming metal at room temperature, what kind of forging will you prefer?

A: Cold forging Cold forging is preferred for deforming objects near room temperature.

Q: A cylindrical billet that is 100 mm long and 50 mm in diameter is reduced by indirect (backward)…

A: Dear student According to the guidelines I am allowed to answer only first three…

Q: An austenitic stainless steel plate with a width of 100 mm, a length of 150 mm and a thickness of 50…

A: Given: The width of the plate, w = 100 mm The length of the plate, L = 150 mm The height of the…

Q: Explain why and how various factors influence springback in bending of sheet metals.

A: Plastic deformation in the material is always followed by the elastic recovery, since the elastic…

Q: Why single shear strength is greater than double shear?

Q: A 3in long and 1in diameter billet is extruded in a direct extrusion operation with an rx = 4.0. The…

A: Write the extrusion ratio. rx=4 Write the length and diameter of the billet. L=3 inD=1 in…

Q: A connecting rod is designed for hot forging in a printing die. The projected area of the part is…

A: Given Data Ap=6500 mm2 A=9000mm2 σf=75Mpa To Find the maximum force required to execute the…

Q: A round billet made up of beryllium, 200 mm in diameter is extruded at 900°C to a diameter of 100mm.…

Q: Write a detailed note on "Hydrostatic Extrusion". Also draw diagrams to explain the process of…

A: "Hydrostatic Extrusion" is a form of "direct hot extrusion process". It is done at a temperature…

Q: A solid cylindrical slug made of 304 stainless steel is 150 mm in diameter and 100 mm high. It is…

A: Given:Initial diameter of cylinder, do=150 mmInitial height of the cylinder, ho=100 mmDiameter after…

Q: Explain steps of extrusion process in forming process?

A: Extrusion is forming process in which material is allowed to move through a die which results in…

Q: A force of 1100 KN is applied to punch a 40-mm-diameter hole in a plate. If the shear strength is…

Q: A brass billet is to be extruded from its initial diameter of 100 mm to a final diameter of 50 mm,…

A: Given: Initial diameter. do= 100 mm or 102 mm Final diameter. d1 = 50 mm

Q: To what thickness can a solid cylinder of 6061-0 aluminium, that is 20 mm in diameter and 50 mm…

Q: A round wire made from 1020 carbon steel is being drawn from a diameter of 12.5 mm to 9.5 mm in a…

A: Empirical relation for F in terms of yield strength, area ratio, friction coefficient and die angle…

Q: Illustrate the advantages of direct extrusion on indirect extrusion

A: The direct extrusion process is the most well-known extrusion used in the expulsion business. It…

Q: A direct extrusion operation produces a product with a 20 mm x 60 mm cross sectional area from a…

Q: A direct extrusion process is used to reduce a cylindrical part that has a diameter of 5 inch and is…

Q: A spool of wire has a starting diameter of 2.5 mm. It is drawn through a die with an opening that is…

A: givenspool of wire has a starting diameter di= 2.5 mma die with an opening that is df= 2.1…

Q: * A cylindrical workpiece made of 1100-0 Aluminum that is 18 in high and 16 in in diameter and is to…

A: The forging force for open die forging is 1.3 MN.

Q: Write down what you know about extrusion defects or rolling defects

A: Let us discuss about defects in rolling or extrusion processes.

Q: The true strain is

Q: Describe the effect that extrusion has on material properties with examples

A: Extrusion is a process that confines a metal in a closed cavity by allowing it to flow from only a…

Q: A cylindrical billet that is 100 mm long and 50 mm in diameter is reduced by indirect (backward)…

Q: A strip with cross-sectional area 150 mm x 4.5 mm is being rolled with 20% reduction of area using…

Q: Assuming that an average forging pressure of 340 Mpa is required,what is the largest closed-die…

A: Given: P=340 MPa F=350 MN

Q: A company produces aluminum alloy billets with dimensions of 250mm diameter and 500 mm length by…

Q: Q7_What is the difference between true strain and engineering strain? What is the relationship that…

Q: Draw and explain drop forging process. Write any three common forging materials and mention its…

Q: An open die forging operation is performed to produce a steel cylinder with a diameter o 9.7mm and a…

Q: Using open-die forging operation, a solid cylindrical piece of S.S. having 100 mm diameter and 72 mm…

A: Forging is a metal-shaping method in which metal is shaped by applying focused compressive stresses.…

Q: A cylindrical billet that is 80 mm long and 32 mm diameter is reduced by backward extrusion to a 12…

Q: (1) Calculate the extrusion force ( N or mega newton) required for round billet of 70-30 brass which…

Q: What is K constant in sheet metal bending? How to calculate shear force and extrusions? Formulas?

A: When sheet metal bends, the bend allowance is given byLb=αR+ktWhere ,Lb=is the bend allowance α=bend…

Q: In open-die forging, a disc of diameter 200 mm and height 60 mm is compressed without any barreling…

A: Given data as per question The initial diameter of disc =200 mm Height of disc =60 mm The final…

Q: You have been asked to work on some design problems and technically support the team working on…

Q: A typical plastic shopping bag made by blown film has a lateral dimension (width) of 550 mm. Assume…

A: Given:- Width=550mm Expanded from 1.5 to 2.5 times To find:- Die diameter size

Q: Write a detail note on direct extrusion process.

A: Different types of extrusion processes are: Direct Extrusion Indirect Extrusion Hydrostatic…

Q: What are extrusion defects?

Q: What is the difference between drawing and extrusion?

A: Extrusion It is a Process where a billet is forced through a die parts have constant cross-section…

Q: A hole is to be punched out on a layer of papers using a puncher with a hole diameter of 100 mm. If…

A: Given:d=100 mmσc=15.1 MPat1=125*10-3 mmζs=13.5 MPa

Q: A billet 75mmlong and 25mmin diameter is to be extruded in a direct extrusion operation with…

A: Given data Length = 90mm Diameter = 25 mm Extrusion ratio = 4.0 Strength coefficient = 415 Mpa…

Q: A billet 100 mm long and 40 mm diameter is to be extruded in a direct extrusion with final diameter…

A: Given data A billet 100 mm long and 40 mm diameter is to be extruded in a direct extrusion with…

Q: A cylindrical part with initial diameter of 45 mm and the initial height of 40 mm is upset forged in…

A: Given Data: The initial diameter is di=45 mm. The initial height is hi = 40 mm. The final height is…

Question

In open-die forging, a disc of diameter 200 mm and height 60 mm is compressed without any barreling effect. The final diameter of the disc is 400 mm calculate the true strain.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

In open-die forging, disc of diameter 200 mm and height 60 mm is compressed without any barreling effect. The final diameter of the disc is 400 mm. The true strain is
A cylindrical part is warm upset forged in an open die. The initial diameter is 50 mm and the initial height is 40 mm. The height after forging is 30 mm. The coefficient of friction at the die-work interface is 0.25. The yield strength of the work material is 285 MPa, and its flow curve is defined by a strength coefficient of 600 MPa and a strain-hardening exponent of 0.12. Calculate the strain at yield point.
Write a detailed note on "Hydrostatic Extrusion". Also draw diagrams to explain the process of hydrostatic extrusion.
Write down what you know about extrusion defects or rolling defects
What is K constant in sheet metal bending? How to calculate shear force and extrusions? Formulas?
A round slug 10 mm in diameter and made of a metal with average flow stress 300 MPa is reduced to a final diameter of 7 mm by cold extrusion. Estimate the force on the punch.
An austenitic stainless steel plate with a width of 100 mm, a length of 150 mm and a thickness of 50 mm is to be hot forged in a hydraulic press so that the width remains constant. If it is to be reduced in one step to a thickness of 40 mm, calculatea) the actual load that needs to be applied at the end of the forging, as well as b) the corresponding deformation energy. In previous plane strain compression tests, it was found that the material exhibits an average plane strain yield stress of 80 MPa at the forging temperature. Assume that the efficiency of the process is 0.6 Answer: Pfr= 2.5 MN ; WTr= 25 kJ
A 3in long and 1in diameter billet is extruded in a direct extrusion operation with an rx = 4.0. The extrusion has a cross section. The angle of the die (half angle) is 90o. The work metal has a resistance coefficient of 60ksi and a strain hardening exponent of 0.18. Use Johnston's formula with a = 0.8 and b = 1.5 to estimate the extrusion stress. Determine the pressure applied to the end of the billet when the piston moves forward.
A copper strip of 200 mm width and 300 mm thickness is to be rolled to a thickness of 295 mm The roll of radius 300 mm rotates at 100 rpm. The average shear strength of the work material is 180 MPa. Calculate the roll strip contact length and the roll force .
A solid cylindrical slug made of 304 stainless steel is 150 mm in diameter and 100 mm high. It is reduced in height by 50% at room temperature by opendie forging with flat dies. Assuming that the coefficient of friction is 0.2 and the flow stress of this material is 1000 MPa, calculate the forging force at the end of the stroke. Manufacturing processes
A 300mm thick slab is being cold rolled using roll of 600mm diameter.If the coefficient of friction is 0.08. Determine the maximum possible reduction.
A typical plastic shopping bag made by blown film has a lateral dimension (width) of 550 mm. Assume the tube is expended from 1.5 to 2.5 times the extrusion die diameter. Calculate the extrusion die diameter size.