In order to form a stream of bubbles, air is introduced through a nozzle into a tank of water at 20°C. If the process requires 4.0 mm diameter bubbles to be formed, by how much the air pressure at the nozzle must exceed that of the surrounding water? What would be the absolute pressure inside the bubble if the surrounding water is at 100.3 kN/m2?Take surface tension of water at 20°C = 0.0735 N/m. *

In order to form a stream of bubbles, air is introduced through a nozzle into a tank of water at 20°C. If the process requires 4.0 mm diameter bubbles to be formed, by how much the air pressure at the nozzle must exceed that of the surrounding water? What would be the absolute pressure inside the bubble if the surrounding water is at 100.3 kN/m2?Take surface tension of water at 20°C = 0.0735 N/m. *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A vertical cylindrical container contains 5840 gallons of gasoline and is 1.53 m in radius. Due to evaporation within the tank, the pressure on the top of the fluid is 2.5 times normal atmospheric pressure. The density of gasoline is 737 kg/m3. a. What is the pressure at the bottom of the tank? b. If a nozzle at the bottom of the tank is used to let fuel out, with what velocity would the gasoline exit the hole? c. If a nozzle at the bottom of the tank is used to let fuel out, what volume flow rate will result if the diameter of the hole is 1.2 cm? d. At what initial rate will the height of the fuel level in the tank drop as fuel is removed?
A steel tape 0.5 mm thick and 20 mm wide is pulled by a force ? through a slit opening 1.5 mm and length 15 mm. Considering that the tape is centered on the slit, that lubricating oil of viscosity µ = 0.4 ??-2? fills the gap spaces not occupied by the tape and that the maximum tape speed is 10 m/s, calculate the maximum force ? .
An oil gusher shoots crude oil 23.0 m into the air through a pipe with a 0.100 m diameter. Neglecting air resistance but not the resistance of the pipe, and assuming laminar flow, calculate the pressure (in N/m2) at the entrance of the 45.0 m long vertical pipe. Take the density of the oil to be 900 kg/m3 and its viscosity to be 1.00 (N/m2) · s (or 1.00 Pa · s). Note that you must take into account the pressure due to the 45.0 m column of oil in the pipe.
Determine the velocity profile within a 12 µm diameter capillary, with a viscosity of 4 cP, and a pressure gradient of 25 mm Hg/500 µm. Assume that gravitational effects can be ignored and that the blood vessel is perfectly cylindrical.
Air is flowing parallel to the plate at U∞=5 m/s and T∞=300 K over the flat plate of length L=0.1 m anddepth of 1 m into the paper, at the atmospheric pressure at the same temperature as the plate. Find;a) Boundary layer thickness at the point x = L of the plateb) Find the total resistance force acting on the two surfaces of the plate.c) The velocities in the hydrodynamic boundary layer are measured by a hot wire anomemeter. Thevelocity at x=0.1 m on the x component is measured as u=3 m/s. Find the distance from the plate and they component of velocity v.
Air at 20°C and 1 atm flow past the flat plate in Fig.under laminar conditions. There are two equally spacedpitot stagnation tubes, each placed 2 mm from the wall.The manometer fluid is water at 20°C. If U = 15 m/s andL = 50 cm, determine the values of the manometer readingsh1 and h2, in mm.
Consider air flowing past a hemisphere resting on a flatsurface. If the internal pressure is pi, findan expression for the pressure force on the hemisphere. At what point A on the hemisphereshould a hole be cut so that the pressure force willbe zero according to inviscid theory?
An oil drop has a density (?1) of (560+R) kg/m3. The terminal velocity of a spherical drop of thisoil falling in air at the room temperature is (15 + R) cm/s. At the room temperature, air density(?2) is 1.2 kg/m3and its viscosity is 18 μPa.s. Find the radius of the droplet. Consider g =9.81 ??
A block of weight W is being pulled over a table by anotherweight W o , as shown in Fig. Find an algebraic formulafor the steady velocity U of the block if it slides on an oil film of thickness h and viscosity μ . The block bottomarea A is in contact with the oil. Neglect the cord weightand pulley friction. Assume a linear velocity profile inthe oil film.
Estimate the speed of sound of carbon monoxide at 200-kPa pressure and 300°C in m/s.
A large plate is pulled at a constant speed of U = 4 m/s over a fixed plate on 5-mm-thick engine oil film at 20°C. Assuming a half-parabolic velocity profile in the oil film, as sketched, determine the shear stress developed on the upper plate and its direction. What would happen if a linear velocity profile were assumed?
How big is the viscous force acting on the 1 μm-radius droplet when it is moving with terminal velocity? On the 10 μm droplet?