6 In order to pull out the nail at B, the force F exerted onthe handle of the hammer must produce a clockwisemoment of 200 lb in about point A as shown in(Figure 1).Figure< PreviousEt18 in.30⁰5 in.< 1 of 1Part ADetermine the required magnitude of force F.Express your answer in pounds to three significant figures.F =Submit—| ΑΣΦ 41Request Answervec69°F Mostly cloudyIE 18 in.30⁰5 in.

In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a clockwise moment of 200 lb in about point A as shown in (Figure 1). Figure < Previous 5: 18 in. 30° 5 in. < 1 of 1 S LOP ▼ Part A Determine the required magnitude of force F. Express your answer in pounds to three significant figures. F = —| ΑΣΦ 41 vec Submit Request Answer 69°F Mostly cloudy CO

In order to pull out the nail at B, the force F exerted on the handle of the hammer must produce a clockwise moment of 200 lb in about point A as shown in (Figure 1). Figure < Previous 5: 18 in. 30° 5 in. < 1 of 1 S LOP ▼ Part A Determine the required magnitude of force F. Express your answer in pounds to three significant figures. F = —| ΑΣΦ 41 vec Submit Request Answer 69°F Mostly cloudy CO

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.75P: The end of a water hose weighing 0.5 lb/ft is pulled with a 40-lb force that is inclined at 14 to...

See similar textbooks

Similar questions

The end of a water hose weighing 0.5 lb/ft is pulled with a 40-lb force that is inclined at 14 to the horizontal. Determine the length s of the hose that is lifted off the ground and the corresponding horizontal distance L.
Determinethe magnitude (lb) of the horizontal component of force at point C if P = 135.7 lb, x = 13.1 in, y = 6.9 in, and z = 8.8 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction : use L if to the left or R if to the right.
The forklift supports the engine. Determine the force that this load generates on element FB. Write your answer in Newtons. Consider Engine mass = 148 kg a = 1.47 m b = 2.21 m
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=651N, Y=232N, Z=134, a=5.7m and b=3.2m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the magnitude (lb) of the horizontal component of force at point C if P = 130.9 lb, x = 14.3 in, y = 7.4 in, and z = 6.8 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use L if to the left or R if to the right.
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member CD if X=593N, Y=238N, Z=158, a=3m and b=3.4m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the absolute value of the force at point O in [N] ? m = 30 kg F=422 N w = 8 rad/s
1) Determine the force acting on the hydraulic cylinder BC. Express your answer in pounds to three significant figures. 2) Determine the horizontal and vertical components of reaction at the pin A(Ax,Ay). Express your answers in pounds to three significant figures separated by a comma.
1) Determine the horizontal and vertical components of reaction at A(Ax,Ay) . Express your answers in newtons to three significant figures separated by a comma 2) Determine the force in the cable BC . Express your answer to three significant figures and include the appropriate units.
The 50 N force is applied to the lever cutter handle. Determine the force exerted by the cutting blade in part E. Dimensions in mm.
Replace the loading by an equivalent resultant force. (Figure 1) Suppose that w1 = 5 lb/ft, w2 = 2 lb/ft, and F = 80 lb. a) Determine the magnitude of the resultant force. Express your answer in pounds to three significant figures. b) Specify the location of the force on the beam, measured from A. Express your answer in feet to three significant figures.
Determine the force that the wall exerts on the aluminum rod at point B after the temperature change. (Give your answer in kN and to 0 decimal places.) Determine the force that the wall exerts on the brass rod at point A after the temperature change. (Give your answer in kN and to 0 decimal places.)