Consider a change of basis from a Cartesian to the rotated Cartesian frame shown in Fig. 2. By studying the figure, you should recognize that strains €rx, Eyy, Ery, after transformation into the coordinate system rotated by relative to the original coordinate system, are simply Err, E90, Ero at a point (r, 0). Use the change of basis formula for a second-order tensor to write the strain components Err, €00, Ero as a function of €xx, Ery, Exy and 0.

Consider a change of basis from a Cartesian to the rotated Cartesian frame shown in Fig. 2. By studying the figure, you should recognize that strains €rx, Eyy, Ery, after transformation into the coordinate system rotated by relative to the original coordinate system, are simply Err, E90, Ero at a point (r, 0). Use the change of basis formula for a second-order tensor to write the strain components Err, €00, Ero as a function of €xx, Ery, Exy and 0.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stress tensor below is given for x, y, z coordinate system. Find the stress tensor if x, ycoordinates are rotated 45° clockwise.[?] = 4 1 2 1 6 0 2 0 8
For the two-dimensional stress field shown in Fig. suppose thatσxx = 2000 lbf/ft2 σyy = 3000 lbf/ft2 σn(AA) = 2500 lbf/ft2Compute ( a ) the shear stress σ xy and ( b ) the shear stress onplane AA .
An ex vivo sample of human skin is experimentally subjected to a displacement field given by the attachment where A is a constant. Determine: a. small strain tensor b. Lagrange strain tensor c. whether there are differences between the small strain tensor and Lagrange strain tensor. Explain under what conditions the two tensors would be approximately equal.
Transforming the coordinates of the shear stress from cartesian to spherical coordinate system allows to better visualize the dynamics of the tensor on a spherical geometry. True or False
The stress tensor at a point is given below. Determine: a) All principal stresses. b) Unit normal vectors in all principal directions. c) The maximum shear stress. d) 3D Mohr's circle with calculations and labelling key values.
If n1 is an eigenvector for a strain tensor, prove it is also a principal direction for the stress tensor.
Find the kinematic viscosity of an oil having density of 980kg/m^2 when at a certain point in the oil, the shear stress is 0.25 Pa and the velocity gradient is 0.3 m/s.
The surface tensions of mercury and water at 60 degrees Celcius are 0.47N/m and 0.0662 N/m, respectively. What capillary height changes will occur in these two fluids when they are in contact with air in a glass tube of radius 0.30mm? Use θ = 130° for mercury, and 0° for water; y = 132.3 kN/m3 for mercury and 9.650 kN/m3 for water. Provide the given along with its solution.
In a stream of glycerine in motion, at a certain point the velocity gradient is 0.25 meter per sec per meter. The mass density of fluid is 1268.4 kg per cubic meter and kinematic viscosity is 6.30 x 10^-4 square meter per second. Calculate the shear stress in Pascal at the point.
For the pressure-gradient fl ow between two parallel platesof Fig. 4.12( b ), reanalyze for the case of slip fl ow at bothwalls. Use the simple slip condition u wall = l( du / dy ) wall ,where l is the mean free path of the fl uid. ( a ) Sketch theexpected velocity profi le. ( b ) Find an expression for theshear stress at each wall. ( c ) Find the volume fl ow betweenthe plates.
Show with tensors and in three-dimensional space that all directions are principal axes for the stress state at a point where τ1=τ2=τ3
A smooth square cylinder is put in 15 °C flowing water. The flow direction is perpendicular to the long axis of the cylinder (parallel to the square section). The edge length of the square is s=2.0m. The long axis length is L=5.0m. The flow velocity is v=0.046 m/s. The density of water is ρ=1000kg/m3. T he dynamic viscosity is η=1.15×10-3kg/m·s. (3) Calculate the drag force FD_________N (2 decimal places)