In orthogonal turning of a cylindrical tube of wall thickness 5 mm, the axial and the tangential cutting forces were measured as 1259 N and 1601 N, respectively. The measured chip thickness after machining was found to be 0.3 mm. The rake angle was 10° and the axial feed was 100 mm/min. the rotational speed of the spindle was 1000 rpm. Assuming the material to be perfectly and Merchant's first solution, the shear strength of the material is closest to

In orthogonal turning of a cylindrical tube of wall thickness 5 mm, the axial and the tangential cutting forces were measured as 1259 N and 1601 N, respectively. The measured chip thickness after machining was found to be 0.3 mm. The rake angle was 10° and the axial feed was 100 mm/min. the rotational speed of the spindle was 1000 rpm. Assuming the material to be perfectly and Merchant's first solution, the shear strength of the material is closest to

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A slab-milling operation is carried out on a 200 mm long, 80-mm-wide annealed mild-steel workpiece having a feedrate of 0.1 mm/tooth and a depth of cut of 4.0 mm. The cutter of 50 mm diameter has 18 straight teeth and rotates at 135 rpm. The given specific energy for this material is 3.5 W s/mm3 and the slab mill is wider than the workpiece to be machined. Calculate:‧ the material-removal rate;‧ the power and torque required for this operation;‧ the cutting time. (243 mm/min, 77760 mm3/min, 4.5 kW, 52.8 s)
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
A mild steel block of width 40 mm is being milled using a straight slab cutter 70 mm diameter with 30 teeth. If the cutter rotates at 40 rpm, and depth of cut is 2 mm, what is the value of maximum uncut chip thickness when the table feed is 20 mm/min?
A circular shape blank will be cut of 107 mm diameter from a strip of 3.5 mm with a clearance value of 0.25 mm. Take the shear strength as 400 MPa. Determine The appropriate punch diameter. Blanking force. Blanking force when the blade angle is 5.70 o.
What force is required to punch a ½ - inch hole on a 3/8 thick plate if the ultimate shearing strength of the plate strength of the plate is 42000 psi and a factor of safety of 2?
A 78 mm thick plate is to be milled down to a thickness of 60 mm using an 80 mm face milling cutter. Calculate the processing time if the cutting depth is 6 mm, the feed/rev is 1.1 mm and the cutting speed is 15 m/min, and if the over run for a 620 mm long plate is 10 mm.
(USCS units) A turning operation is performed using a rake angle of 15°. Cutting speed = 200 ft/min, feed= 0.012 in/rev, and depth of cut = 0.100 in. The chip thickness ratio measured after the cut = 0.48. Determine (a) chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain (USCS units) The turning operation in the previous problem involves a work material whose shear strength = 52,000 lb/in2. Based on your answers to the previous problem, compute (a) shear force, (b) cutting force, (c) thrust force, and (d) friction force.
Manufacturing Process In a turning operation on stainless steel with hardness = 200 HB, the cutting speed = 200m/min, feed = 0.25 mm/rev, and depth of cut =7.5 mm. Determine how much power will the lathe machine draw in performing this operation if its mechanical efficiency = 90 %. Use specific energy value is: U = 2.8 J/mm
A shaft of 0.5 m in length and 100cm in diameter is to be machined. What operation will you utilize on lathe to bring the specimen of size 50 cm diameter and 0.25 m length?
In a turning operation, cutting speed =200 m/min; feed = 0.25mm mm/rev, and depth of cut = 4.00mm Thermal diffusivity of the work material = 20m mm^2/s and volumetric specific heat =3.5(10^ -3 )J/mm^ 3 -C If the temperature increase above ambient temperature (20degreesC) is the angle measured by a tool-chip thermocouple to be 700degreesC, determine the specific energy for the work material in this operation.
Low carbon steel having a tensile strength of 450 MPa and a shear strength of 270 MPa is cut in a turning operation with a cutting speed of 2500 mm/s. The feed is 0.15 mm/rev, and the depth of cut is 0.25 cm. The rake angle of the tool is 12° in the direction of chip flow. The resulting chip ratio is 0.55. Using the orthogonal model as an approximation of turning, determine (a) the shear plane angle, (b) shear force, (c) cutting force and feed force.
A student is performing a turning operation with a workpiece with an initial diameter of 40 mm to produce a 30 mm diameter rod that is 100 mm long. The lathe power is 20 kW and is operating on 85% mechanical efficiency. If the student set the cutting speed to 0.5 m/min and the cutting tool is set to have a rake angle of 5 degrees: a.) What material can we choose for the rod is the coefficient of friction is 0.5? b.) If we select 4130 normalized heat-treated steel for the rod, and coefficient of friction is 0.5, what will the maximum depth of cut we can achieve?