In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the rings at A and B, respectively. If s = 0 when the cylinders are removed, determine the following: 2 m +1m 2 m This is not your 1.5 m ppperty do any ww kAC 1.5 s m m d to yu Note: Use 9.81m/s² for the gravitational constant and kBp=134 N/m. icate y be su ww

In the assembly shown, sags of s and 1.5 s resulted when the two cylinders were suspended from the rings at A and B, respectively. If s = 0 when the cylinders are removed, determine the following: 2 m +1m 2 m This is not your 1.5 m ppperty do any ww kAC 1.5 s m m d to yu Note: Use 9.81m/s² for the gravitational constant and kBp=134 N/m. icate y be su ww

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Similar questions

The load is supported by the four 304 stainless steel wires that are connected to the rigid members AB and DC. Determine the vertical displacement of the 500-lb load if the members were originally horizontal when the load was applied. Each wire has a cross-sectional area of 0.025 in2.
other given: T(sub B) = 80.11 T = 5.67 kN-m
The device is used to measure a change in temperature. Bars AB and CD are made of A-36 steel and 2014-T6 aluminum alloy, respectively. When the temperature is at 75°F, ACE is in the horizontal position. Determine thevertical displacement of the pointer at E when the temperature rises to 150°F.
ANSWER: h0.26916 m Show the complete solution.
he region of safety in maximum shear stress theory contains which of the given shape *
A steel rod is acted upon by the loading shown below. 50 mm2is the area of the circular rod. The coupling sizes at B, C, and D are neglected. Use E st = 200 GPa.
The three-bar truss in Fig. a is subjected to a horizontal force of 5 kip. If the cross-sectional area of each member is 0.20 in2, determine the horizontal displacement at point B. E = 29(103) ksi.
The driver of the sports car applies his rear brakes and causes the tires to slip. If the normal force on each rear tire is 1800 N and the coefficient of kinetic friction between the tires and the pavement is { { \mu }_{ k }=0.5 }μk=0.5, determine the average shear stress developed by the friction force on the tires. Assume the rubber of the tires is flexible and each tire is filled with an air pressure of 225 K P
A six-pack is shaken so that the pressurein each can is p = 20 psi. A board is placed onthe six pack and a student(s) weighing Wstands on the board so his weight is evenlydistributed to the six cans. The aluminumproperties are E = 10,000 ksi, Sy = 35 ksi, andν = 0.33. Each can has an average radius ofR = 1.25 in., thickness t = 0.01 in., and lengthL = 4.50 in.(a) Determine the critical weight of thestudent, Wcr , so that a stress element on thesurface of the can is in a state of uniaxial stress.Assume that no support is provided by thecontained liquid and the cans do not fail bybuckling (being crushed). (b) Determine thestrain in the longitudinal direction of the candue to pressure p = 20 psi and force Wcr.(c) Determine the strain in the hoop directionof the can due to pressure p = 20 psi and forceWcr
The steel chisel has a diameter of 0.5 in. and a length of 10 in. It is struck by a hammer that weighs 3 lb, and at the instant of the impact it is moving at 12 ft>s. Determine the maximum compressive stress in the chisel, assumingthat 80% of the impacting energy goes into the chisel. Est = 29(103) ksi, sY = 100 ksi
The collar has a weight of 50 lb and falls down the titanium bar. If the bar has a diameter of 0.5 in., determine the largest height h at which the weight can be released and not permanently damage the bar after striking the flange at A. Eti = 16(103) ksi, sY = 60 ksi.
A 37.5-mm-diameter rod 6 mlong elongates 12 mm under a load 236 KN. Thediameter of the rod decreases 0.025 mm during theloading. Determine the following properties of thematerial: (a) Poisson’s ratio.(b) Young’s modulus(c) The modulus of rigidity.