Answered: In the circuit shown below, resistor A…

In the circuit shown below, resistor A is dissipating 22.5 W and 4 A of current is flowing through resistor B. Calculate the resistance of B. A 10 s2 B

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter21: Current And Direct Current Circuits

Section: Chapter Questions

Problem 33P: A battery has an emf of 15.0 V. The terminal voltage of the battery is 11.6 V when it is delivering...

See similar textbooks

Similar questions

Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0 resistor, (b) Find the current in the 3.00-12 resistor.
A child's electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 inseries with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and itsbatteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
Consider the circuit shown in Figure P18.11. Find (a) the potential difference between points a and b and (b) the current in the 20.0- resistor. Figure P18.11
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
Three 60.0-W, 120-V lightbulbs are connected across a 120-V power source, as shown in Figure P18.50. Find (a) the total power delivered to the three bulbs and (b) the potential difference across each. Assume the resistance of each bulb is constant (even though, in reality, the resistance increases markedly with current). Figure P18.50
Calculate the power delivered to each resistor in the circuit shown in Figure P21.43. Figure P21.43
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
A child’s electronic toy is supplied by three 1.58-V alkaline cells having internal resistances of 0.0200 in series with a 1.53-V carbon-zinc dry cell having a 0.100- internal resistance. The load resistance is 10.0 . (a) Draw a circuit diagram of the toy and its batteries, (b) What current flows? (c) How much power is supplied to the load? (d) What is the internal resistance of the dry cell if it goes bad, resulting in only 0.500 W being supplied to the load?
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19
Figure P18.19 shows a Wheatstone bridge, a circuit used to precisely measure an unknown resistance R by varying Rvar until the ammeter reads zero current and the bridge is said to be balanced. If the bridge is balanced with Rvar = 9.00 , find (a) the value of the unknown resistance Rand (b) the current in the 1.00 resistor. (Hint: With the bridge balanced, the wire through the ammeter can effectively be removed from the circuit, leaving two pairs of resistors in parallel.) Figure Pl8.19