In the distribution transformer; In the transformer used for the distribution of electricity to the houses, 3.3 kilovolts enters and 400 volts come out. When we make the phase-neutral calculation, that is, when we divide it by √3, we get 230 volts and 220 volts coming to the sockets. Where does the remaining 10 volts go? (Can you explain with figure)

In the distribution transformer; In the transformer used for the distribution of electricity to the houses, 3.3 kilovolts enters and 400 volts come out. When we make the phase-neutral calculation, that is, when we divide it by √3, we get 230 volts and 220 volts coming to the sockets. Where does the remaining 10 volts go? (Can you explain with figure)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.34MCQ: Consider Figure 3.25 of the text for a transformer with off-nominal turns ratio. (i) The per-unit...

See similar textbooks

Similar questions

Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
As a production engineer in Super Power Electrical Technology Sdn. Bhd., you have been givena responsibility to upgrade the transformer’s efficiency in electrical appliances providing in yourbranch office. The company's director asked you to present the criteria for the selection oftransformers to be used in the development of oven products. Those criterions listed below arethe key areas that you need to take account in the appliances’ upgrading process: i) State and explain the possible factors affecting the transformer’s efficiency. ii) Evaluate the conditions needed to fulfil the maximum efficiency. iii) Determine and justify the calculation of transformer’s efficiency.
Draw a simple block diagram for a 24V stand-alone residential PV system powering both DC and AC loads. Show PV array, inverter, battery bank, charge controller, and AC & DC loads. Show PV array modules wired together as 2 series and 4 parallel (2s x 4p) and show their polarity (+ and – terminals) charging a lead-acid battery bank wired 2s x 8p. Show all major components and conductor polarities. For overcurrent devices and disconnects in the appropriate conductor you can simplify in the appropriate leg and show and as a small combined block labeled:
A transformer is to be used to match an 8-Ωloudspeaker to a 500-Ω audio line. What is the turnsratio of the transformer, and what are the voltages atthe primary and secondary terminals when 10Wofaudio power is delivered to the speaker? Assume thatthe speaker is a resistive load and that the transformeris ideal.
Now that a 1:15 step-up transformer is installed at the output of the generator and a 15: 1transformer is installed at the end of the transmission line, as depicted in Figure Q3(b). (i)Determine the new load voltage/generated voltage ratioand power loss in the transmission line. (ii)By assuming the transformer is ideal, evaluate your answers with those obtained in 3(a)
As an Engineer you have been contracted by a power distribution company to investigate the causes of frequent transformer failures in its network. In the course of your investigation you came across the following: The Transformer installed in urban area failed within the warrant period of 3 years; the diagnostic results showed failure of one phase of the High Voltage (HV), It was further observed that this failure was causes by Overheating and overloading of that phase which caused burning of both HV and Low Voltage (LV). Explain what could be the cause(s) of this overload and the implications it could have on other equipment in the Transformer
????????????:• Write the GIVEN with their respective symbols and units.• Do not skip the SOLUTIONS, do it step-by-step with their respective symbols and units???????:Calculate the all-day efficiency of a 100-KVA transformer operating under the following conditions:6 hour, 50 kW, 0.73 pf3 hours, 90 kW, 0.82 pfIron loss = 1000 wattsOne quarter load Copper loss = 66.25 wattsa) The rest of the day, transformer running idleb) The rest of the day, primary disconnected from the source.
A 400-turns auto transformer, operating in the step-down mode with 25 percent tap supplies a 4.8 kVA, 0.85 lagging power factor load. The input to the transformer is 2400 V, 60 Hz. Neglect the small losses and leakage effects. What will be the apparent power(in kVA) conducted and transformed respectively?
TOPIC: Power Systems, Power Plants & IlluminationINSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A 55000-kW thermal plant of National Power Corporation delivers an annual output of 238000000 kw-hr with a peak load of 44 MW. What is the capacity factor? 49.4% 42.4% 48.2% 44.6%
Draw an HVDC system with proper arrangement of converters. Evaluate its technical and economic feasibility comparing with 3-phase AC line .
Since R1=18.10Kohm, R2=67.58Kohm, RC= 1.08Kohm, RE= 3.23Kohm, VCC=14.00V, Beta=241.00 in the circuit given in the figure, calculate the IC current by doing a complete analysis. When performing your operations, 2 steps will be taken after the point. choose the closest one from the stylish ones according to the +/-10% margin of error. There is only 1 correct answer to the question.
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices