In the drawing operation, technological property weldability is an important parameter. Select one: O True O False

Q: In sheet metal parts, the minimum bending radius is dependent on which of the following elements? a.…

A: given: In sheet metal parts, the minimum bending radius is dependent on which of the following…

Q: The mode of deformation of the metal during spinning is (a) Bending (b) Stretching (c) Rolling and…

A: Given Data⇒Mode of deformationmetalSpinningProblem definition⇒Problem says choose the correct…

Q: 7) Which of the following types of stresses are induced in the stretch forming process? Tensile…

A: Stretch forming: It is a type of sheet metal forming process in which raw material (sheet metal) is…

Q: 21 Forging process is suitable for mass production. Select one: True False

A: Forging is the metal forming process in which heat treatment is done on the metal up to 75% of its…

Q: What is "term paper" and its parts/contents?

A: A term paper is a research paper which is written by students at the end of a school semester.

Q: Forging process is suitable for mass production. Select one: True False

A: Forming process: It is a mechanical process in which the plastic deformations is done for the…

Q: What are the steps for drawing?

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Identify the forming process in which the rectangular shape of the cross section is reduced into…

A:

Q: engineering materials and processes introduction about forging and welding

A: Forging is a manufacturing process, which is used for making different shapes of metals. This…

Q: Extrusion and drawing have numerous application in manufacturing continuous as well as discrete…

A: Extrusion: It is a metal forming process in which a material under high pressure is forced through…

Q: 32- Which of the following is the machine in which the extrusion process is made? A) paint can B)…

A: Extrusion process In extrusion process the material is compressed in the cylinder. The deformed…

Q: Question # 3 Using ONLY neat sketches show the basic elements and differences in the following: (1)…

A:

Q: Open-die forging (upsetting) involves reduction of height of a specimen between two flat dies using…

A: Forging is the forming process in which metal is shaped by applying force using hammer or…

Q: a). Briefly explain the drop forging process with a neat diagram. b). Explain the wire drawing…

A: The above both process are used for manufacturing process.

Q: 104) Which is not one of the methods used to specify geometric features in technical drawing? A)…

A: When multiple questions are asked only first question has to be solved.  Please post the other…

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is second.

Q: Aluminium and copper wires can be made by cold drawing process. Select one: O True O False

A: True

Q: What important quantity (or quantities) can be determined by measuring striation spacing?

A: Striation Spacing: Striation Spacings are the marks that are produced at the mating surfaces of the…

Q: a). Briefly explain the drop forging process with a neat diagram. b). Explain the wire drawing…

A:

Q: Which is not a copolymer type? a) block B) wavy C) casually D) graft E) complex •44- Which one is…

A: coplymers are  Block type, alternative(wavy) type, Casually (Random) type, graft type. geometry of…

Q: The main part of the product consists of a polyurethane sponge

A: • Strength & Durability:When the upholstery is produced using high grade resins, only a thinPU…

Q: In drawing process _force is used to reduce the cross sectional area of the workpiece. a. Pushing b.…

A: Drawing may be a metalworking process which employments malleable forces to extend metal, glass,…

Q: Check and state in your answer booklet which of the following statements is False and which is True.…

A: 1) False- Elastic region is characterised by proportional relationship between stress and strain.…

Q: When the instantaneous load is applied parallel to the specimen cross section, the material is under…

A: As per given question  When the instantaneous load is applied parallel to the specimen cross…

Q: What is the Strain Rosettes?

A: Strain rosette is the combination of three liner strain gauge placed in three direction. The measure…

Q: 1) Which of the following statement(s) is/are correct? i. Cold-rolling is used to produce sheet and…

A: Explanation1)Due to low temperature in cold-rolling operation no scale formation takes place. so it…

Q: 1) Selection of die in forging process is very important in order to control the quality of the…

A: Basics requirements for die material; 1)They should accurately reproduce all fine details in the…

Q: (c) An arc welding is performed to join two metal pieces. After the welding process, the product is…

A: As given the two metals are welded using arc welding then a fatigue test is done on it. Fatigue…

Q: Briefly describe which type of axonometric drawing is most commonly used in industry?

A: In industry there are three types of axonometric drawings used they are 1.Isometric Projection 2.…

Q: 57. In gas welding process, rubber is used as preferred material for hoses. Select one: True False

A:

Q: is appi perpendicular to the specimen cross section, th material is under a significant

A: Ans: Engineering stress

Q: 14 1. Wrinkling II. Tearing III. Earing IV. Surface scratches Which are some of the possible defects…

A:

Q: 1) The stresses and strains in metal forming are of which type? Elastic_plasticultimate…

A: 1)  Answer- metal forming involves Plastic deformation.   2) Answer - compression stress explanation…

Q: xtrusion is a fundamental shaping process. Describe it

A: Yes,Extrusion is a basic shaping process.

Q: In the drawing operation, mechanical property ductility is an important parameter. Select one: True…

A: Ductility is a mechanical property that describes how easily a substance can be drawn into a wire.…

Q: The most common industry that uses open die forging process is ________. a. Hospitals b. University…

A:

Q: Forging process is suitable for mass production. Select one: True False

A: Forging:-              Forging is the process in which material is shaped by the application of the…

Q: 1- The use of lubricant in wire drawing die.

A: we have to discuss the use of lubricant in wire drawing

Q: What happens to the surfaces of a material when it is bent?

A: Consider the diagram shown below for the bending of the sheet metal.

Q: In drawing process, compressive forces are used to reduce the cross section of the workpiece.

A: In the above statement, it is mentioned that compressive force is applied in drawing process to…

Q: Differ between Constant Load and Cross-Sectional Area?

A: Constant load otherwise called Point load (P) is a force applied at a single infinitesimal point at…

Q: Hot rolling is carried at temperature lower than melting temperature of materials Select one: True O…

A:

Q: Examine the following isometric drawings of the surfaces of conversion coatedmetals. Which do you…

A: From the above given figures, the surface A with 1200 Angstrom (0.12 micron) gap between the two…

Q: What are two differences between clamshell/beach markings and fatigue striations?

A: clamshell are larger as compared to the striations It represent the location of the crack tip. It…

Q: 2. A paper below has a shear strength of 10 MPa. What must be the applied force to cut the paper…

A:

Q: Forging process is suitable for mass production. Select one: True False

A: Forging is a manufacturing process in which metals are plastically deformed, using a die or hammer,…

Q: 3) Collapsible tubes are made by Drawing Spinning Rolling Impact extrusion

A:

Q: In the drawing operation, mechanical property ductility is an important parameter. Select one:…

A: Ductility is a mechanical property commonly described as a material's amenability to drawing,…

Q: The temperature range of hard soldering process is __________________. a. 183-212 C. b. 650-700 C.…

A: Answer is (b) 650-700 C

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.