in the elastmoer-in-shear coupling the teeth are staright, this allows for more_______ than a jaw coupling. whats the answer?

Q: 71) Which is not a surface texture parameter? A) roughness B) cutting length C) array D) wavy E)…

A: As per our guideline we can answer only one question at a time ,you are requested to post other…

Q: What will the number of pairs of teeth in contact if arc of contact is 31.4mm andmodule is equal to…

A:

Q: Explain the operation of roll over protection

A: Rollover protection is a structural design that is used to protect the operator of heavy machines.…

Q: What is the relationship between the degrees of freedom and the types of joints?

A: Given: Relationship between the degree of freedom and the types of joints

Q: Which fastener type would require the smallest positional tolerance (if all other design parameters…

A: In this problem, it is asking about the type of fastener that requires the positional tolerance to…

Q: An ASE automotive grade bolt with three slash marks on its head, indicates a hardness of what grade…

A:

Q: QUESTION 25 The direction of sliding of kinematically permissible wedges is less restrictive than…

A: Rock mechanism and fundamentals concept  ***As per our company policy we are supposed to do only 3…

Q: Explain mist type lubrication system, write its advantages and disadvantage?

A: Given Mist Type lubrication system To find Working Advantage Disadvantage

Q: what is a flanged coupling ?

A: Coupling : It is mechanical device which connects two shafts for power transmission from the driving…

Q: What is the total length of Tailstock ?

A:

Q: Write the compatibility equation. Give consideration as to how it supports constrain shaft when it…

A: The compatibility equation make restriction to obtain how a strain can vary in a body for an assumed…

Q: Why is it important that the applied torques must not cause yielding of thematerial?

A: Torque causes twist in the cross sections of the member on which it is applied. If the applied…

Q: What are the Bar Cutter's OBJECTIVES/PURPOSE

A: A bar cutter is a machine tool designed to cut bars of metal. There are several types of bar cutters…

Q: 8) The main failure mode of worm drive is A. Fatigue pitting of tooth surface C. The bonding and…

A: Gear drive is used to transmit or reduce the transmission ratio. A worm drive is the most effective…

Q: 99) which is more important for assembly than its values? A) yield strength B) hardness C) size D)…

A:

Q: An SAE 1050 Cold drawn steel is to be used for a square or rectangular key. The shaft is made of…

A: In numerical problems the values are to be round of to the nearest next value If the value is less…

Q: Name and define the basic components of rotary equipment? Provide at least one example of each…

A: Rotary equipment is a common type of mechanical equipment that is used to induce the kinetic energy…

Q: a. What are the general rules of lubrications? b. Mention with examples the different methods of…

A: NOTE: As per our expert guidelines we are supposed to answer only first 3 subquestions. Post…

Q: What are the mechanical problems are associated with an ESP?

A: Given ESP To find Mechanical problem

Q: . What elastomer sealing materials could be used with a petroleum-base fluid if the operating…

A: Elastomers (also known as rubbers) are a versatile group of materials that are used in…

Q: The length, width and thickness of a steel sar Its thickness needs to be uniformly reduced milling.…

A: GivenD=100mmw=50mmz=20toothN=1200rpmft=0.05mm/tooth revf=z×ftf=20×0.05f=1mm/rev

Q: one of the advantages of elastromer couplings over flexible metal couplings is that what?

A: Advantages of elastomer couplings over flexible metal are as given below 1. Elastomeric couplings…

Q: For the manufacture of a pipe wrench would you select: a. Fe-0.4%C steel b. Fe-0.4C steel abs case…

A: Pipe wrenches are available in different sizes from 3 inches to 48 inches or larger. A pipe wrench…

Q: s loaded by a uniformly distributed torque of intensity stance what is the angle of twist between…

A: Given data as per questionL=Length of prismatic bard=Diameter of bart=Intensity of Uniformly…

Q: Angle of- approach Angle of recess Position - of teeth entering contact Position of teeth leaving…

A: P is the pitch point

Q: 1. If maximum stress is 200Mpa, stress amplitude is 50Mpa, minimum stress is 100Mра. ( ) 2. For the…

A:

Q: In a kinematic chain, a quaternary joint is equivalent to

A: The kinematic chain is defined as the combination of the kinematic links in such a way that the…

Q: By your own word, explain thin film bearings?

A: According to Bartleyby's policy we can answer only oe question at a time so if you want other parts…

Q: 1- Name the different forms of journal bearings. 2- Sketch with freehand and name the different…

A: Journal Bearings

Q: -.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer…

A: Given data: The diameter of the bolt is D = 24 mm. The length of the bolt is L = 100 mm. Here, the…

Q: which best manufaring process use to manufacture carbon steel segment gear?

A: There are so many processes to manufacture segment gear. These are given as, (1) Casting: Sand…

Q: What is cohesiveness precisely? How is a tight connection distinguished from a loose coupling?

A: Cohesiveness: The act or state of sticking together tightly between the same nature of atoms. The…

Q: In a bolted tension joint, the proper fastening torque, T, is proportional approximately to what…

A:

Q: How’s ASTM D2041 related to ASTM D2726 ??

A: Solution is attached below:

Q: ce every 2 weeks (10 working days). Lead time is 2 days. The company has deter- ned that the average…

A:

Q: the combination shear and compression elastromeric coupling is designed for what?

A: The combination shear and compression elastomeric coupling is designed for transmitting torque…

Q: I want proper solution don't copy from others solution I will report. flange coupling connects two…

A: To find: The minimum bolt diameter required to transmit the same torque that the shaft can transmit.…

Q: Q.1 Why is a special type of CV grease used to lubricate a Birfield/Rzeppa joint?

A: Note: Since you have asked multiple question, we will solve the first question for you. If you want…

Q: where are thread sealers most often used?

A: Thread sealers is the product that seals the gap between male and female thread.

Q: G=? IGX E?

A:

Q: 9. From the couplings listed below, select the mechanical couplings Rigid coupling • Flexible…

A:

Q: raking torque applied?

A: Given; A force, F=400 NApplied to the brake drum of diameter, d=0.5 mWrapping angle,…

Q: What are couplings? When are they used?

A: Couplings: It is a mechanical device that connects two shaft which is used to transmit power from…

Q: what type of analysis is done in connecting rod Linear static analysis or dynamic analysis

A: Given Connecting rod To find Type of analysis

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.