TRUE OR FALSE. ANSWER ALL QUESTIONS OTHERWISE DONT ATTEMPT IT STRICTLY. I WILL REPORT YOU IF U ATTEMPT WITHOUT ANSWERING ALL QUESTIONS. 1. If maximum stress is 200Mpa, stressamplitude is 50Mpa, minimum stress is100Mpa. ( )2. For the bolt assembly, there is thread in thehole.()3. The final stage of fatigue failure isformation of micro cracks.4. Stud is used fasten a part with a throughhole and a part with blind tapped hole.()5. Gears are used in the case of large centerdistance.()

Answered: Image /qna-images/answer/9ffef2bb-9d4e-472f-a65a-570731e413fd.jpg

1. If maximum stress is 200Mpa, stress amplitude is 50Mpa, minimum stress is 100Mра. ( ) 2. For the bolt assembly, there is thread in the hole. () 3. The final stage of fatigue failure is formation of micro cracks. 4. Stud is used fasten a part with a through hole and a part with blind tapped hole. () 5. Gears are used in the case of large center distance,

1. If maximum stress is 200Mpa, stress amplitude is 50Mpa, minimum stress is 100Mра. ( ) 2. For the bolt assembly, there is thread in the hole. () 3. The final stage of fatigue failure is formation of micro cracks. 4. Stud is used fasten a part with a through hole and a part with blind tapped hole. () 5. Gears are used in the case of large center distance,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Screw M14*2 Fasten with a hexagonal nut The bolt material meets the requirements within the 4.8 property class and the nut material belongs to the 5 property class Find the largest tensile strength of the bolt that can be tolerated without breaking
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a. the threaded shank, b. the head against being sheared off, and c. the bearing surface under the head. d. Is there any need to consider the strength of standard cap-screw heads in design?
A cap screw, ¾ in.-10-UNC-2, with a hexagonal head that is 9/16 in. thick, carries a tensile load of 3000 lb. If the material is AISI 1015, cold drawn, find the factor of safety based on ultimate strengths of a.the threaded shank, b.the head against being sheared off, and c.the bearing surface under the head. d.Is there any need to consider the strength of standard cap-screw heads in design?
Question: Suppose that the fatigue data for the steel alloy in Problem 9.12 were taken for bending-rotating tests, and that a rod of this alloy is to be used for an automobile axle that rotates at an average rotational velocity of 600 revolutions per minute. Give the maximum lifetimes of continuous driving that are allowable for the following stress levels: (a) 450 MPa (65,000 psi), (b) 380 MPa (55,000 psi), (c) 310 MPa (45,000 psi), and (d) 275 MPa (40,000 psi). Reference: Problem 9.12 is listed below (only use for reference but does not need to be solved). The tensile strength of brittle materials may be determined using a variation of Equation 9.1. Compute the critical crack tip radius for an Al2O3 specimen that experiences tensile fracture at an applied stress of 275 MPa (40,000 psi). Assume the acritical surface crack length of 2 x 10-3 mm and theoretical fracture strength of E/10, where E is the modulus of elasticity.
Is the maximum shear stress theory is based on the idea of slipping that occurs in ductile failure?
A bronze bearing supports the steel shaft shown in the figure. The shaft has a Brinell hardness (HB) of 150 and a diameter of 30 mm. The bearing has a length of 30 mm. Estimate the depth of adhesive wear to expect from the shaft if it rotates at 200 rpm for 4 years (three 8-hour shift per day, 260-day per year) if the transverse load is 2000 N. Poor lubrication is expected between the shaft and the bearing.
A motor is used to drive a gear assembly at 200 rpm. The main gear is in the center of a 1 m long (0.5 m to the left and right of the gear) 50 mm diameter solid circular shaft, and power is taken from the two shaft ends. 25 kW is taken on the left end and an unknown amount of power is taken at the right end. the torque to the left side of the gear is? maximum shear stress to left of gear? If the maximum shear stress on the shaft to the right of the gear is 125 MPa, approximately how much power is being drawn off from the right side of the shaft? The shaft can be made from 6061-T6 aluminum. It has adequate strength to withstand the loading conditions in the scenario, including the loading on the right side of the shaft. true or false?
Having trouble with finding torsional Shear stress for xy and zy. Thank you
Choose the correct answer: - In a set of meshing gears, forces are transmitted on ….. which is normal to the contacting surfaces. a) Pitch angle b) Base circle c) Line of action d) Pitch radius - The pressure line is tangent to which circles of the gear and pinion? a) Pitch circles b) Base circles c) Addendum circles d) Dedendum circles - Which one is correct about brittle materials? a) They show a considerable plastic deformation. b) Distortion energy theory is an acceptable theory to describe the failure in these materials. c) They exhibit catastrophic failure.
Question: Draw a potential to failure curve and explain its characteristics briefly.
What are the mechanics of torque tube failure and the failure pattern?
1. A jack having square threads of 50 mm nominal diameter and 10 mm pitch is supporting a load of 89 kN. A double thread is used and the coefficient of friction maybe as low as 0.10 or as high as 0.15.c. What maximum torque is necessary to lower the load?d. What is the maximum torsional shear stress induced on the screw?