In the figure, a lead brick rests horizontally on cylinders A and B. The areas of the top faces of the cylinders are related byA4= 1.6 Ag; the Young's moduli of the cylinders are related by EA= 2.3 Eg. The cylinders had identical lengths before the brickwas placed on them. What fraction of the brick's mass is supported (a) by cylinder A and (b) by cylinder B? The horizontaldistances between the center of mass of the brick and the centerlines of the cylinders are dafor cylinder A and dg forcylinder B. (c) What is the ratio da/dg?dacom of brickAВ(a) Numberi 0.73UnitsThis answer has no units(b) Numberi 0.27UnitsThis answer has no units(c) Numberi0.37UnitsNo units

Answered: Image /qna-images/answer/d3f55fe9-861b-4671-b034-8bd1159e919c.jpg

Answered: In the figure, a lead brick rests…

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 82PQ

See similar textbooks

Similar questions

A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately.
A uniform beam resting on two pivots has a length L = 6.00 m and mass M = 90.0 kg. The pivot under the left end exerts a normal force n1 on the beam, and the second pivot located a distance = 4.00 m from the left end exerts a normal force n2. A woman of mass m = 55.0 kg steps onto the left end of the beam and begins walking to the right as in Figure P10.28. The goal is to find the womans position when the beam begins to tip. (a) What is the appropriate analysis model for the beam before it begins to tip? (b) Sketch a force diagram for the beam, labeling the gravitational and normal forces acting on the beam and placing the woman a distance x to the right of the first pivot, which is the origin. (c) Where is the woman when the normal force n1 is the greatest? (d) What is n1 when the beam is about to tip? (e) Use Equation 10.27 to find the value of n2 when the beam is about to tip. (f) Using the result of part (d) and Equation 10.28, with torques computed around the second pivot, find the womans position x when the beam is about to tip. (g) Check the answer to part (e) by computing torques around the first pivot point. Figure P10.28
A stepladder of negligible weight is constructed as shown in Figure P10.73, with AC = BC = ℓ. A painter of mass m stands on the ladder a distance d from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P10.73 Problems 73 and 74.
A stepladder of negligible weight is constructed as shown in Figure P12.40, with AC = BC = = 4.00 m. A painter of mass m = 70.0 kg stands on the ladder d = 3.00 m from the bottom. Assuming the floor is frictionless, find (a) the tension in the horizontal bar DE connecting the two halves of the ladder, (b) the normal forces at A and B, and (c) the components of the reaction force at the single hinge C that the left half of the ladder exerts on the right half. Suggestion: Treat the ladder as a single object, but also treat each half of the ladder separately. Figure P12.40 Problems 40 and 41.
A uniform wire (Y = 2.0 1011 N/m2) is subjected to a longitudinal tensile stress of 4.0 107 N/m2. What is the fractional change in the length of the wire?
Two uniform planks, each of mass m = 7.45 kg and length L = 2.51 m, are connected by a hinge at the top and by a chain of negligible mass attached at their centers, as shown in the figure. The assembly will stand upright, in the shape of an A, on a frictionless surface without collapsing. If the chain has the length 0.81 m, find each of the following: a) the absolute value of the tension in the chain, b) the absolute magnitude of the force on the hinge of each p lank
A ladder is leaning against a vertical wall, and both ends of the ladder are at the point of slipping. The coefficient of friction between the ladder and the horizontal surface is ?1=0.195 and the coefficient of friction between the ladder and the wall is ?2=0.203. Determine the maximum angle α with the vertical that the ladder can make without falling on the ground.
A solid uniform ball with mass m and diameter d is supported against a vertical frictionless wall by a thin massless wire of length L. If the ball has a mass of 45 kg and diameter 32 cm, while the wire has a length of 30 cm, what is the tension in the wire?
a uniform beam of length 12.0 m is supported by a horizontal cable and a hinge at angle u =50.0°. The tension in the cable is 400 N. In unit-vector notation, what are (a) the gravitational force on the beam and (b) the force on the beam from the hinge?
A uniform plank of length 5.0 m and weight 225 N rests horizontally on two supports, with 1.1m of the plank hanging over the right support. To what distance x can a person who weighs 377 N walk on the overhanging part of the plank before it just begins to tip?
A spade is modelled as a uniform rod, of mass 2kg and length 90cm, attached to a uniform square lamina, of side 20cm and mass 0.5kg. A gardener holds the spade horizontally with hands 30cm and 60cm from the end of the rod. Find the vertical forces exerted by the gardener's hands. Im stuck on this q, pls help.
In the figure, a lead brick rests horizontally on cylinders A and B. The areas of the top faces of the cylinders are related by AA= 1.7 AB; the Young's moduli of the cylinders are related by EA= 1.9 EB. The cylinders had identical lengths before the brick was placed on them. What fraction of the brick's mass is supported (a) by cylinder A and (b) by cylinder B? The horizontal distances between the center of mass of the brick and the centerlines of the cylinders are dAfor cylinder A and dB for cylinder B. (c) What is the ratio dA/dB?

SEE MORE QUESTIONS

Recommended textbooks for you

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

Principles of Physics: A Calculus-Based Text

Physics

ISBN:

9781133104261

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers with Modern …

Physics

ISBN:

9781337553292

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers: Foundations…

Physics

ISBN:

9781133939146

Author:

Katz, Debora M.

Publisher:

Cengage Learning

Principles of Physics: A Calculus-Based Text

Physics

ISBN:

9781133104261

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers with Modern …

Physics

ISBN:

9781337553292

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Physics for Scientists and Engineers

Physics

ISBN:

9781337553278

Author:

Raymond A. Serway, John W. Jewett

Publisher:

Cengage Learning

Glencoe Physics: Principles and Problems, Student…

Physics

ISBN:

9780078807213

Author:

Paul W. Zitzewitz

Publisher:

Glencoe/McGraw-Hill

College Physics

Physics

ISBN:

9781285737027

Author:

Raymond A. Serway, Chris Vuille

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS