In the figure below (Figure 1), suppose the object is a square steel plate, 10.0 cm on a side and 1.10 cm thick. Find the magnitude of force required on each of the four sides to cause a shear strain of 0.0405.

In the figure below (Figure 1), suppose the object is a square steel plate, 10.0 cm on a side and 1.10 cm thick. Find the magnitude of force required on each of the four sides to cause a shear strain of 0.0405.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter14: Static Equilibrium, Elasticity, And Fracture

Section: Chapter Questions

Problem 50PQ

See similar textbooks

Related questions

Q: What is Hooke’s law for the 1-D system? Choices: The relation between normal stress and the…

A: solution, Hooke’s law is valid up to the proportional limit of a material. here we have 1 D system…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s=…

A: Stress scale, s = 350 Strain scale, ε = 0.010

Q: Stress (MPa) 800 Breaking point 600 Elastic limit 400 200 Eļastic behavior Strain 0.002 0.004 0.006…

Q: A steel wire of length 2.08 m with circular cross section must stretch no more than 0.300 cm when a…

A: Write the formula for Young’s modulus.

Q: I Review | Constants In the figure below (Figure 1), suppose the object is a square steel plate,…

Q: What is the stress? a) It is force per unit area and can be expressed as the ratio of the applied…

A: The object gets deformed when some deforming force is applied on it.

Q: An object with a mass equal to 300 kg is hung on a wire of length 5.00 m and cross-sectional area of…

A: Write the given values with suitable variables. m=300 kgL=5 mA=0.25×10-4 m2E=8×1010 N Here, m is the…

Q: The “lead” in pencils is a graphite composition with Young’s modulus of approximately 1.0×109 N/m2.…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: The lateral strain acting in a body is defined as: A or D Select one: a. the strain perpendicular to…

A: lateral strain is defined as the ratio of the change in diameter of a circular bar of a material to…

Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…

A: stress is defined as the force per unit area. Write the expression for stress. S=FA…

Q: For a constant force, a rope breaks due to stress. Which of the following is useful to reduce the…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: Given data- The figure shows the stress strain curve for a material for which, Stress s=320 in…

Q: After a fall, a 110 kg rock climber finds himself dangling from the end of a rope that had been 15 m…

Q: A 586-N object is hung from the end of a wire of cross-sectional area 0.04 cm2. The wire stretches…

Q: A steel rod 250 mm long is subjected to a tensile stress. If its change in length is 1/40 mm, what…

A: Given: Steel rod length, L=250 mm Change in length, ∆L=140 mm Steel Young's Modulus, γ=2×105 N/mm2…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: A 542-N object is hung from the end of a wire of cross-sectional area 0.07 cm2. The wire stretches…

A: Applied force, F = 542 N Area of cross section, A = 0.07 cm² = 0.07 × 10-4 m² Original length, L =…

Q: A rubber cord and a steel wire are each subjected to linear stress. Draw sketch graphs showing how…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s=…

A: The stress-strain curve is shown below.

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by…

A: Given : scale of the stress axis is set as s=320 in a unit of 106N/m2 ε=0.0090

Q: how can I derive formula to find the original volume, given the bulk modulus, change in volume and…

A: The bulk modulus is defined as the ratio of the volumetric stress to the volumetric strain.

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: A sign (mass 2500 kg) hangs from the end of a vertical steel girder with a cross sectional area of…

Q: Suppose a vertebra is subjected to a shearing force of 540 N. Randomized Variablesf = 540 N h = 2.9…

A: Write the given values with the suitable variables. F=540 Nh=2.9 cm=0.029 md=4.3 cm=0.043 mS=80×109…

Q: A material with a rectangular cross-section of 5 mm by 10 mm is loaded in tension with a force of 16…

Q: The bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…

A: bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of…

Q: Which of the following is a dimensionless quantity? Select one: a. Shear stress b. Poison's ratio c.…

A: As we dimensionless quantity are those which have no dimensions i.e M0 L0 T0

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: (a) Write the given data. σ=320 106 N/m2ε=0.0040

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set bys =…

A: s = 350 ×106 Nm2ε = 0.010

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s -…

A: Given: S = 300 in units of 106 N/m2 ε = 0.010 Solution: a) From the given graph, we have…

Q: A material is made in circular rod form of diameter 0.6 cm and 10 cm long . It is fixed on the…

A: Dear student The strain is defined as Change in length per unit original Length. Strain = ∆L/L

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: The stress-strain graphs for materials X and Y are shown. Strain Strain graphs are drawn to the same…

A: ( a ) Comparing the two graphs we can infer that the stress on X is greater than that on Y for the…

Q: (b) In the diagram below Fig Q2(b), forces are applied along three different axes to a 100 mm cube…

A: This question is based on Mechanical Properties of Solids topic. Bulk Modulus is the ration of Bulk…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: Young's modulus of nylon is 3.7 × 109 N/m2. A force of 6.0 × 105 N is applied to a 1.5-m length of…

A: Given data: The Young's modulus of nylon is E=3.7×109 N/m2. The force applied is F=6.0×105 N. The…

Q: The figure shows Force-Displacement curve for natural rubber. What can be said about the rubber…

A: Rubber is an elastic material. When an external force is applied to the rubber, it changes its…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: Young's modulus is a measurement of a material's capacity to endure length changes when subjected to…

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

A: Given: s = particular value of stress shown in the graph = 250 x 106 N/m2 ε = particular value of…

Q: Consider a rod, when applied with a certain force, reverts to its original form. With stress given…

A: Data Given , Stress = 3 Gpa Strain = 0.230 We have to find out the Young's modulus of the rod = Y

Q: The figure shows the stress-strain curve for a material. The scale of the stress axis is set by s =…

Q: The Force of resistance per unit area offered by a body against deformation is the stress? 10:36 PM…

A: The force resistance to deform the per unit area body is known as stress

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

In the figure below (Figure 1), suppose the object is a square steel plate, 10.0 cm on a side and 1.10 cm thick.

Find the magnitude of force required on each of the four sides to cause a shear strain of 0.0405.

Express your answer in newtons.

In the figure below (Figure 1), suppose the object is a
square steel plate, 10.0 cm on a side and 1.10 cm thick.
Part A
Find the magnitude of force required on each of the four sides to cause a shear strain of 0.0405.
Express your answer in newtons.
?
Figure
1 of 1
F =
F,
Submit
Request Answer
Fy
Provide Feedback
F,V
F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.
I already asked this question on here before, but it had a value I did not recognize at all, and it was wrong anyways. I am posting the question again because I still cannot get it, and I have tried different ways to go about solving this. In the figure below (Figure 1), suppose the object is a square steel plate, 10.0 cm on a side and 1.10 cm thick. Find the magnitude of force required on each of the four sides to cause a shear strain of 0.0405. Express your answer in newtons.
The bulk modulus of a material is 5.62 × 1011 N/m2. What fractional change in volume does a piece of this material undergo when it is subjected to a bulk stress increase of 3.91x107 N/m2? Assume that the force is applied uniformly over the surface. Round your answer to 3 decimal places.
how can I derive formula to find the original volume, given the bulk modulus, change in volume and bulk stress?
a metal rod with length 2 m and cross sectional area of 0.002 m2 has a youngs modulus of 20x10^10Pa. if a force of 5000n is exerted on the end of the rod. What is the strain? What is the stress? a block with volume 500cm3 is subjected to a pressure increase of 10x10^6 Pa and the volume decreased by 0.50cm3 what is the bulk modulus of the block pls answer both :( thank you
Please type it in 5 sentences. In your own words, what is the purpose of finding out the maximum shear force and bending moment that a beam may experience as it supports loads?
A metallic cube whose each side is 10cm is subjected to a shearing force at 10kg wt. The top face is displayed through 0.25cm with respect to the bottom. Calculate the shear stress , shear strain and shear modulus.
A 586-N object is hung from the end of a wire of cross-sectional area 0.04 cm2. The wire stretches from its original length of 150 cm to 150.4 cm. What is the stress on the wire? Answer: ______ N/m2 help asap
The graph below represents the stress versus strain for a particular material. What is the Young's modulus (in N/m2) for this material? N/m2
A steel wire of length 1.93 m with a circular cross-section must stretch no more than 0.240 cm when a tensile (stretching) force of 350 N is applied to each end of the wire. What minimum diameter dmin is required for the wire?Express your answer in millimeters. Take Young's modulus for steel to be Y = 2.00×1011 Pa .
A hollow member having the cross section shown is formed from steel alloysheet of 2mm thickness. Knowing that the shearing stress must not exceed 3MPa, (a) determine the largest torque that can be applied to the member and (b) using the largest torque calculated in (a), determine the angle of twist (Shear modulus of steel alloy is assumed 75 GPa).
What is proportional bulk strain?