In the figure shown, there are 38 meters of 5-cm diameter pipe, 23 meters of 15-cm diameter pipe, and 46 meters of 8-cm diameter pipe, all cast iron. The flow rate is 4.53 L/s of water and the technical details of the pipe are shown below. For cast iron, ε = 0.26 mm Sharp 5-cm entrance: K = 0.5 5-cm bend: K = 0.95 5-cm sudden expansion: K = 0.79 8-cm open globe valve: K= 6.3 a) Determine the total friction losses in the pipes in series. b) Calculate the total minor losses. c) Compute the mechanical power extracted by the turbine. Elevation 30 5 cm dia. Open Turbine Globe 15 cm dia. 8 cm dia. 23 m 23 m 19 m 19 m 8 cm dia. 23 m Elevation 0

In the figure shown, there are 38 meters of 5-cm diameter pipe, 23 meters of 15-cm diameter pipe, and 46 meters of 8-cm diameter pipe, all cast iron. The flow rate is 4.53 L/s of water and the technical details of the pipe are shown below. For cast iron, ε = 0.26 mm Sharp 5-cm entrance: K = 0.5 5-cm bend: K = 0.95 5-cm sudden expansion: K = 0.79 8-cm open globe valve: K= 6.3 a) Determine the total friction losses in the pipes in series. b) Calculate the total minor losses. c) Compute the mechanical power extracted by the turbine. Elevation 30 5 cm dia. Open Turbine Globe 15 cm dia. 8 cm dia. 23 m 23 m 19 m 19 m 8 cm dia. 23 m Elevation 0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A fluid flow in 75mm diameter pipes at a rate of 0.002 m^3/sec. Determine whether the flow is laminar or turbulent Hydrogen (v = 1.28x10^-4 m^2/s) Air (v = 1.41x10^-5 m^2/s) Gasoline (v = 4.09x10^-7 m^2/s)
An oil has 0.62 inch steel tube, through which flows an oil. The properties of oil are as follows; μ = 0.034 lbs/ft-sec, μb = 0.044 lbs/ft-sec, μw = 0.004 lbs/ft-sec, and specific gravity at 60°F is 0.899. The oil neters at a temperature of t1 = 60°F and flows with an average velocity of 4 ft/sec. The inside ssurface area is 0.1613 ft2 per feet length, and the inside sectional area is 0.3019 in2. The length of one pass of the tube is 10 feet. Considering steam at 215°F surround the tubes. Assume that the inside surface temperature of the pipe is 210°F and a bulk temperature of 72°F. If the specific heat of oil is 0.5 btu/lbs-°F and its conductivity k = 0.08 Btu-ft/hr-F-ft2, what is the temperature at the end of 10 feet pass. Show your complete solution and illustration.
6 cm-diameter commercial steel pipeline is used to transport water at 10⁰C from a reservoir to a free discharge point. The pipeline consists of 85 m straight pipe, 2 wide open gate valves, 1 wide open angle valve, 4 standart 90⁰ elbows, 1 entrance from a reservoir and 1 free discharge. The elevation of the entrance is 10 m while the elevation of the discharge is 35 m. The inlet pressure is 20 psig and exit pressure is 0 psig. A pump is installed in the line to move the water. Calculate the pump work (J/kg) so the volumetric flow rate will be Q= 0.01 m3/s. (1 psi = lbf/in2).
Pressure Drop of Power-Law Fluid in Laminar FlowA power-law fluid having a density of 1041 kg/m3 is flowing through 14.9 m of a tubing with an inside diameter of 0.0524 m at an average velocity of 0.0728 m/s. The rheological or flow properties of the fluid are K′ = 15.23N·sn′/m2 (0.318 lbf·sn′/ft2) and n′ = 0.40. Calculate the pressure drop and friction loss using Eq. (9.1-10) for laminar flow. Check the generalized Reynolds number to make sure that the flow is laminar. Repeat part (a) but use the friction-factor method
Two oil tanks are connected by two 9-m-long pipes, asin Fig.. Pipe 1 is 5 cm in diameter and is 6 mhigher than pipe 2. It is found that the flow rate in pipe2 is twice as large as the flow in pipe 1. (a) What is thediameter of pipe 2? (b) Are both pipe flows laminar?(c) What is the flow rate in pipe 2 (m3/s)? Neglect minorlosses.
A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at 20 C. a. What is the velocity of the water (average) in the pipe? b. What is the Reynolds number value? c. Is the flow laminar or turbulent?
SAE 30 oil at 20°C flows in the 2.5-cm-diameter pipe as shown in the figure below, which slopes at 37°. For SAE 30 oil, take ρ = 891 kg/m3 and μ = 0.29 kg/m⋅s. Determine the flow rate in m3/h. The flow rate is m3/h.
A horizontal water pipe of 15 cm diameter converges to a 7.5 cm diameter. If the pressures at the two sections are 400 kPa, and 150 kPa respectively, calculate the flow rate of water in cubic meters per second
A 100mm circular sharp edge hole in the end of a 150mm pipe discharges oil (s = 0.90). The vapor pressure in the closed tank is – 20 kPa, and the pressure head on the centerline of the pipe directly upstream from the orifice is 9m of oil. There is no submersion of the discharge. If CV = 0.97 and Q = 83 liters/s, find the discharge coefficient. Answer: C = 0.68
A fluid at 20C flows at 850 cm3/s through an 8 cm diameter pipe. Determine the entrance length if the fluid is (a) hydrogen; (b) air; (c) gasoline; (d) water; (e) mercury; and (f) glycerin.
Water at 25 deg C (998 kg/m 3 ) flows at 10 m 3 /s through a straight pipe of an ID of 1.38 m to 2 m-ID. Consider the level of the entrance and terminal bottom walls of the pipe equal, neglecting the effects of potential energy. In addition, the shaft work is zero. What is the Reynold's number. What kind of flow regime?
A straight 10-cm commercial-steel pipe is 1 km long and is laid on a constant slope of 5°. Water at 20°C flows downward, due to gravity only. For water at 20°C, take ρ = 998 kg/m3 and μ = 0.001 kg/m⋅s. Does the flow rate change with the change in the length of the pipe? Yes or No?