In the following circuit, the supply voltage is defined as V(t) = 325 sin (314t – 30o) and L = 2.2H. Determine the value of the RMS current flowing through the coil and draw the resulting phasor diagram.

In the following circuit, the supply voltage is defined as V(t) = 325 sin (314t – 30o) and L = 2.2H. Determine the value of the RMS current flowing through the coil and draw the resulting phasor diagram.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Related questions

Q: REE - Apr. 1999 16. Determine the gradient of the function f(x, y, z) = x + y +? at the point (1, 2,…

Q: An FM modulator has kf=30kHz/V and operates at a carrier frequency of 180 MHz a. Find the output…

A: FM modulator sensitivity is, kf=30 kHz/Volt Carrier frequency is, fc=175 MHz Instantaneous value of…

Q: 9 baseboards heaters with a rating of 2,000 watts are running in an apartment for 12 Hours. What is…

Q: Q 12 Differentiate between Class A and Class B amplifiers by filling in the table below. Amplifiers…

A: You can easily fill up the table with the information I have provided you below. Please go through…

Q: Most homes use solid copper wire (1.723 x 10^8 ohm-m)having a diameter of 1.63 mm to provide…

Q: A 3-phase synchronous generator has excitation voltage Eo=2.44KV, synchronous resistance Rs = 1792,…

A: Synchronous Generator: A synchronous generator is a synchronous machine that uses electromagnetic…

Q: II. Determine the direction of the induced current loop for each situation (upward or downward) and…

A: 1. For North type , it will form a "dot" inside the ring and current loop will be downward. 2. For…

Q: The circuit is at steady state when the switch closes at time t = 0. Determine v,(0-), v,(0+),…

Q: Question 5. A unity feedback system has the overall transfer function Y(s) R(s) 24 (5s + 3)(2s + 8)…

A: The static error constant can be calculated for the general input functions.

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commnly used poles these poles are used when there is need of low cost…

Q: Question 1 Analyze the circuit given in Figure 1 by using Branch Voltages Method and show EP(t) = 0…

A: The node voltage can be calculated by applying kirchhoff's current law to the nodes and then we can…

Q: The magnetic field of an electromagnetic wave in a vacuum has the following equation, where x is in…

Q: Determine the maximum b it vate for an fsk SignaL with a mark frequency of 48KHZ. aspace frequency…

Q: to bring the process temperature back to the desired value. Once this calculation is complete the…

A: i. To Draw the block diagram that represents the temperature controller mentioned above and label…

Q: For the BJT amplifier circuit below, +12V Rc 6.2 kn S12 kn h 100 h=150 R 18 ka R 2.2 kn 390 0 Re 1.1…

Q: Determine the IB, IC and VCE (β=100) Please show the equation used

A: In this question we will find collector current , base current and collector to emitter voltage...

Q: Prob 3. : A NOR type SR latch has S and R inputs as shown below. Plot the output Q of the SR latch…

Q: Solve for power and complex power for every component

A: In this question, We need to determine the complex power for every component? We know complex…

Q: a 260-tur automobile alternator, magnetic fiux in each turn Cos at, where 8 in webers, w Is the…

Q: An electric field in free space is E = (5z3/ε0) az V/m. Find the total charge contained within a…

Q: a) Using equivalent network (find R4L which is the parallel combination of R4 and RL, this…

Q: For an AM transmitter with an unmodulated carrier power of 100 W that is modulated that is modulated…

A: In this question, If three modulating signals with coefficients of modulation of 0.2, 0.4 and 0.5…

Q: 0/1 IDSS = 20 mA and VP = -6 V for a %3D particular JFET. a) What is ID when VGS = OV? b) What is ID…

Q: H.W Find vo R Vo Ans: 유 =-S

Q: Find the following: (Please show complete solution) - Current after 3.3kohms resistor - Current…

Q: If Figure 6.19 represents the cross sections of two spherical capacitors their capacitances. Let a =…

Q: For an electrically short straight wire antenma vertically abng the z axis, the magnetic vector…

A: Given: For an electrically short straight wit antenna vertically along the x-axis, the magnetic…

Q: Rotating antenna radar system which normally receives age and directional data once each revolution…

A: As rotating antenna radar system uses radio signals which is continuous in nature which has…

Q: Find the ß Rnction, frequency of B function, frequency escillation and R¢ E the circuit shown below?…

Q: QI. Design a combinational circuit that converts a binary coded decimal (BCD) to ( 8,4,-2,-1) code…

Q: Q1: For the open loop poles shown in figure s-plane 1- Find the open loop transfer function 2-…

Q: 1/1 The fixed bias provides good Q- Point stability. It is the most using .bias circuit False True

A: The fixed bias provides good Q-point stability. It is the most using bias circuit. True False…

Q: the 3 terminals of TRIAC are Anode 1, anode 2, gate Anode , cathode , gate Base , emitter ,…

Q: (*+ 2)(y + z)

Q: Rs e = 10 Vrms MA Rsh=S00 Rm=5002 Each diod has an average forwerd resistance of 50e and is…

A: The input RMS voltage = 10 volt So the input maximum voltage =Vm = 102 Here each of the diodes has a…

Q: Q48/ A 3-phase, 6-pole, 50 Hz induction motor develops 3.68 KW at 950 r.p.m. if the stator losses…

Q: EX A.1 Sketch the transfer characteristics defined by Ipss = 10 mA and Vp =-8 V.

A: Given, IDSS = 10 mA VP = -8 V

Q: Determine an expression for a_y in spherical coordinates at P(r=4,8=D0.2n rad,0=0.8t rad).

A: In this question, We need to determine the expression of the ay component if spherical expression…

Q: Q/Exprees the de cinaluunber (85)(-85),2 see complemurst)

Q: For the figure given below and device parameters, what is the value of Va and Vb? Use VD = 0.6 V.…

A: In this question we will find valley point voltage and peak point voltage of given Uni junction…

Q: [Q2] n analog signals each is bandlimited to 8.4kHz. They are sampled at a rate 25% over the Nyquist…

A: The answer is n=4 Please find the detailed solution in below image.

Q: Solve for power and complex power for every component

A: In this question, We are going to calculate the complex power for every component The…

Q: For the circuit shown below, determine the value of the current ix. State any assumptions/theorems…

Q: The vector potential of a magnetic dipole is given by Ho m sin 0 r2 A(r, 0) = %3D where m is…

Q: 1. Draw AM modulator Block Diagram 2. Draw all the signals 3. Write the equation for Modulating…

Q: Represent the I1 network of Fig. 13.60 asS an equivalent linear transformer with zero initial…

Q: •9 In Fig. 29-39, two long straight wires are perpendicu- lar to the page and separated by distance…

A: In this question we have given two long straight wires we will find magnitude and direction of…

Q: 18. For the network in Fig. 18, find the branch current through the resistor R3. R1 R3 I3 R5 + + E…

Q: Which of the following is not an advantages of the SCR *

A: Advantages of SCR: 1) It gives noiseless operation at high effeciency. 2) It has no moving parts.…

Q: 13] A transmission line circuit consists of an air transmission line of length 175.752 and…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Concept explainers

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
An alternating voltage given by v = 120 sin (240t + п / 4) V, is applied to a coil withnegligible resistance and inductance of 100 mH. Determine (a) the reactance of thecoil, and (b) the RMS current flowing through the circuit.
A 30 Ω resistor and a reactor coil (inductor coil) with a 0.2 H inductance and negligible resistance are connected in series across a 120 V, 25 Hz supply. Determine: the impedance of the circuit. the current. the true power in watts taken by the circuit. the power factor. the phase angle
Find the instantaneous and RMS voltage of the series RC circuit if the circuit element has R = 10 ohms, L = 24mH. The total instantaneous current is i(t) = 10 sin 377t, amps. Show your solution using 2 different approaches.
In the circuit below, the source is at 50 Hz, the rms voltage is 140 V, R = 100 Ω, L = 500 mH. It Find the average current value for the circuit. (Take as β= 240 degrees) lesson: power electronics
A coil impedance of 68Ω is connected and the circuit has capacitance of 0.002mF is connected to a 215V, 50 Hz supply. Calculate (a) the current flowing, (b) the phase difference between the supply voltage and current, (c) the voltage across the capacitance and (d) the voltage across the resistor. Draw the phasor diagram.
coil connected to a 300V ,50Hz sinusoidal supply takes a current of a 12A at a phase angle 40° .Calculate the industance of the coil
A relay coil is connected to a 210V, 50Hz supply. If it has a resistance of 30Ω and an inductance of 0.5H, calculate thea pparent power and the power factor.
The impedance coil absorbs 250 watts when connected across 220 V, 60 Hz mains, it is then connected across 110 V, 25 Hz mains and also absorbs 250 watts. What is the inductance of the coil? Show complete solution.
A capacitor of 3.18 microfarads is connected in parallel with a resistance of 2000 ohms. The combination is further connected in series with an inductance of 795 mH and resistance of 100 ohms across a supply given by e=400 sin + 80 sin(3wt + 60O). Assume w = 314 rad/sec, determine the rms value of the total current.
Two equal voltages are out of phase with respect to each other by 90 electrical degrees. If the resultant is 311 Volts, what is RMS value of each one?-write legibly-show the complete solution