In the Joule-Gay Lussac's experiment, two vessels connected by a closed valve are submerged in a well-insulated tank containing water bath. Initially vessel 1 holds gas and 2 is evacuated. When the valve is opened the gas flows into vessel 2 and conditions become uniform in vessel 1 and 2. During the process, which following statement is correct Vessel Vessel 2 P1, V1, T1

In the Joule-Gay Lussac's experiment, two vessels connected by a closed valve are submerged in a well-insulated tank containing water bath. Initially vessel 1 holds gas and 2 is evacuated. When the valve is opened the gas flows into vessel 2 and conditions become uniform in vessel 1 and 2. During the process, which following statement is correct Vessel Vessel 2 P1, V1, T1

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

A turbine is supplied with steam at a gauge pressure of 1.4 MPa. After expansion in the turbine the steam flows into a condenser which is maintained at a vacuum of 710 mmHg. The barometric pressure is 772mm Hg. Express the inlet and exhaust steam pressures in pascals (absolute).density of mercury = 13.6x103 kg/m3
9. The gas density is 0.75 kg per cubic meters and air density is of 1.15 kg per cubic meter. If thedriving pressure is 0.25 KPA. Determine the height of the chimney. 10. A powerplant situated at an altitude having an ambient air of 96.53 KPa and 23.88 degreeCelsius. Flue gases at a rate of 5.0 kg per second enter the stack at 200 degree Celsius andleaves at 160 degree Celsius. The flue gases gravimetric analysis are 18% CO2, 7% O2 and 75%N2. Calculate the height of the stack necessary for a driving pressure of 0.20 KPaKindly answer all please. Thank you
Steam generators are a type of heat exchanges that are used inpower plants to generate steam at desired pressure andtemperature (Fig. Q1.b). In a steam generator, saturated liquidwater at 30°C enters a 60-mm diameter tube at the volume flowrate of 12 L/s. After exchanging heat with hot gas, the waterchanges to steam and leaves the generator at a pressure of 9 MPaand a temperature of 400°C. During this process, the diameter ofthe water/steam tube does not change. Where necessary, assume air as an ideal gas and consider R = 287J/(kg.K), Cp = 1005 J/(kg.K), Cv = 718 J/(kg.K). (i) Calculate the steam mass flow rate and inlet velocity of the steam? (ii) What is the exit velocity of the steam? (iii) Calculate the rate of heat transfer (in MW) required tochange the phase of liquid water to steam.
A compressed air tank is designed to contain 50 standard cubic feet of air when Ölled to a gaugepressure of 200 atm at an ambient temperature of 70 F. Calculate the interior volume of thetank. One standard cubic foot of air occupies one cubic foot at standard temperature and pressure(T = 59 F and p = 2116 lb/ft2).
The capillary pressure for a channel of round cross section can be expressed as a function of the surface tension, the contact angle and the channel radius (the numerical factor is 2). Assume a transition of two coaxial channels of constant round cross sections. The larger one has a diameter of 2 mm and a contact angle of 80 degree, the narrower one a contact angle of 125 degree with the liquid. Calculate the other radius required so a liquid segment having one of its two menisci within either segment experiences a counter pressure of 15 mbar.
Explain the concept of heat transfer, and spontaneity and probability base on the increasing temperature of gas molecules in the chamber.
When boiling food the cooking temperature is limited to about 100° C. Pressurecookers allow for faster cooking by increasing the boiling temperature of water using increased pressure. The pressure within the sealed cooker can be variedby using different weights to seal the vent. A pressure cooker containing 4kgof water is to be used to cook potatoes at 150° C determine (a) what pressureis necessary to maintain the desired boiling temperature and (b) the mass ofthe weight that must be used in order to maintain the pressure determined inpart (a) given a round vent with a diameter of 1cm, (c) if the pressure cookerhas a volume of 10L what is the quality of the steam within the pressure cookerthe instant it reaches temperature, before any steam is vented (assuming allair has been purged from the cooker by this point) , and (d) how long can thepotatoes be cooked at the desired temperature before all the water is boiledaway if heat is being added to the system by a 7000 Watt burner. vf =…
Rank in order, from highest to lowest, the liquid heights h1 to h4 in tubes 1 to 4. The airflow is from left to right.
A tank 3.5 m long and 2.5 m wide contains alcohol of relativedensity 0.82 to a depth of 3 m. A 50 mm diameter pipe leadsfrom the bottom of the tank. What will be the reading on agauge calibrated in Pa connected at a point (a) 150 mm abovethe bottom of the tank; (b) in the 50 mm diameter pipe, 2 mbelow the bottom of the tank; (c) at the upper end of a 25 mmdiameter pipe, connected to the 50 mm pipe 2 m below thebottom of the tank, sloping upwards at 30◦to the horizontalfor 1.2 m and then rising vertically for 600 mm? What is theload on the bottom of the tank?
In a water distribution system, the temperature of water is observed to be as high as 30°C. Determine the minimum pressure allowed in the system to avoid cavitation.
Air in a 10 m3 tank has a pressure of 500 KPa and temperature of 40 degrees Celsius. Determine the mass of air in the tank. (neat hand written)
Nutrients dissolved in water are carried to upper parts of plants by tiny tubes partly because of the capillary effect. Determine how high the water solution will rise in a tree in a 0.0026-mm-diameter tube as a result of the capillary effect. Treat the solution as water at 20°C with a contact angle of 15°. The density of water is 1000 kg/m3.