In the last step of a food supplement production, the food supplement is heated from 25C to 75C while passing through a 12.7 mm diameter thin-walled tube at a speed of 0.2 m / s. Proper heating is provided by an electric resistance heating system wrapped on the outer surface of the pipe. What is the heat flux in a pipe with a length of 10 m? The density of the fluid is given as 1000 kg / cubic meter , heat capacity 4000 J / kg-K, density 2x10^-3 kg / m-s, heat

In the last step of a food supplement production, the food supplement is heated from 25C to 75C while passing through a 12.7 mm diameter thin-walled tube at a speed of 0.2 m / s. Proper heating is provided by an electric resistance heating system wrapped on the outer surface of the pipe. What is the heat flux in a pipe with a length of 10 m? The density of the fluid is given as 1000 kg / cubic meter , heat capacity 4000 J / kg-K, density 2x10^-3 kg / m-s, heat

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.12P

See similar textbooks

Similar questions

The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.
Liquid bismuth flows at a rate of 4.5 kg/s through a 5.0-cm-diameter stainless-steel tube. The bismuth enters at 415◦C and is heated to 440◦C as it passes through the tube. If a constant heat flux is maintained along the tube and the tube wall is at a temperature 20◦C higher than the bismuth bulk temperature, calculate the length of tube required to effect the heat transfe
1-) Air at a temperature of 10 °C flows with a volume flow of 50 L/sec in a horizontal pipe with a diameter of 12 cm and a length of 5 m with ε=2.10-5 m roughness and an inner surface temperature of 50 °C. Assuming that the flow is fully developed, calculate a) the average temperature of the air at the outlet plane, b) the amount of heat transfer. 2-) Calculate the rate at which the average friction coefficient, friction force and heat transfer rate will change if the free flow rate of the turbulent air flowing parallel to the plate over a smooth plate is doubled. Does the result change for constant temperature and constant heat flux conditions; Please evaluate. 3-) A person produces an average of 70 W of heat and loses a quarter of this heat from the head area by natural convection and radiation. Calculate the amount of heat transfer that takes place by a) natural convection and b) radiation in a room at 20 °C, considering the human head as a sphere with a diameter of 25 cm at 35 °C.
Air at 1 atm and 300 °C is cooled as it flows at a velocity of 5.0 m/s through a tube with a diameter of 2.54 cm. Calculate the heat transfer coefficient if a constant heat flux condition is maintained at the wall and the wall temperature is 20 °C above the temperature along the entire length of the tube. (see attached)
Problem 3 (ii): Water at a temperature of 15 °C is flowing steadily in a 6 cm diameter, 25-meter long pipe at an average velocity of 6.0 m/sec. The flow is fully developed. The cross-section is circular. For the wall surface condition where the wall has become degraded due to pitting and deposits such that there is a surface roughness with a height of 0.3 millimeters, find the following:a) The Reynolds number. State whether laminar or turbulent flow is expected.b) The Darcy friction factor, ?.c) The pressure drop over the length of the pipe, and the corresponding head loss.
Water at 20°C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge is 5 m above the floor, and friction losses in the 50-mm pipe from the reservoir to the tower amount to 2.5 J/kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 kW?In this problem, we can assume that the surface of the large reservoir and the absorption tower is at atmospheric pressure, show the complete mechanical energy balance describing the flow system? Take the floor to be at 0 height.
In an oil cooler, 216 kg/h of hot oil enters a thin metal pipe of diameter 25 mm. An equal mass of cooling water flows through the annular space between the pipe and a larger concentric pipe; the oil and water moving in opposite directions. The oil enters at 420 K and is to be cooled to 320 K. If the water enters at 290 K, what length of pipe will be required? Take coefficients of 1.6 kW/m2 K on the oil side and 3.6 kW/m2 K on the water side and 2.0 kJ/kg K for the specific heat of the oil.
A vehicle carrying refrigeration box is moving with a speed of 24 m/s on a road withambient temperature of 323 K. The dimensions of box are 3 m(H) × 4 m (W) × 10 m (L).Assume a wall temperature of 283 K and air flow is parallel to the longest side of the box.Neglecting the heat loss from the front side and backside of the box, calculate heat lossfrom four surfaces. For flow over flat surfaces useNu = 0.036(Re)0.8(Pr)1/3The properties of air at bulk mean temperature are : = 1.165 kg/m3, Pr = 0.701, cp = 1005 J/kg – K,  = 16 × 10–6m2/s
Air at 27 ° C and having a flow rate of 3 x 10-4 kg / s passes through a duct with a 4 mm x 16 mm cross section and 1 m length. 600 W / m2 uniform heat flow is applied from all surfaces of the channel. Determine the temperature of the air and duct surface at the outlet. You can consider the flow as fully developed. (Hint: You can find the average temperature of the flow using the given heat flux)
Exhaust gases at 1 atm and 300°C are used to preheat water in an industrial facility by passing them over a bank of tubes through which water is flowing at a rate of 6 kg/s. The mean tube wall temperature is 80°C. Exhaust gases approach the tube bank in normal direction at 4.5 m/s. The outer diameter of the tubes is 0.035 m, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 0.09 m. There are 16 rows in the flow direction with eight tubes in each row. Assume the air properties at 250°C and 1 atm. The air properties at the assumed mean temperature of 250°C and 1 atm are k = 0.04104 W/m·K ρ = 0.6746 kg/m3cp =1.033 kJ/kg·K Pr = 0.6946μ = 2.76 × 10−5 kg/m·s Prs = Pr@Ts = 80°C = 0.7154 The density of air at the inlet temperature of 300°C (for use in the mass flow rate calculation at the inlet) is ρi = 0.6158 kg/m3. The specific heat of water at 80°C is 4.197 kJ/kg·°C. Determine the temperature…
Exhaust gases at 1 atm and 300°C are used to preheat water in an industrial facility by passing them over a bank of tubes through which water is flowing at a rate of 6 kg/s. The mean tube wall temperature is 80°C. Exhaust gases approach the tube bank in normal direction at 4.5 m/s. The outer diameter of the tubes is 0.035 m, and the tubes are arranged in-line with longitudinal and transverse pitches of SL = ST = 0.09 m. There are 16 rows in the flow direction with eight tubes in each row. Assume the air properties at 250°C and 1 atm. The air properties at the assumed mean temperature of 250°C and 1 atm are k = 0.04104 W/m·K ρ = 0.6746 kg/m3cp =1.033 kJ/kg·K Pr = 0.6946μ = 2.76 × 10−5 kg/m·s Prs = Pr@Ts = 80°C = 0.7154 The density of air at the inlet temperature of 300°C (for use in the mass flow rate calculation at the inlet) is ρi = 0.6158 kg/m3. The specific heat of water at 80°C is 4.197 kJ/kg·°C. Determine pressure…
Problem 3: Water at a temperature of 15 °C is flowing steadily in a 6 cm diameter, 25-meter long pipe at an average velocity of 6.0 m/sec. The flow is fully developed. The cross-section is circular. Determine the following for the following wall surface condition i.e. the wall is smooth plastic; a) The Reynolds number. State whether a laminar or turbulent flow is expected.b) The Darcy friction factor, ?, and then find the pressure drop over the length of the pipe.c) Find the corresponding head loss, and calculate the pressure drop over the length of pipe if the velocity is halved, to 3.0 m/sec for the smooth wall case.