A square isothermal chip is of width 5mm on a side mounted in a substrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of coolant at 15C. From reliability considerations, the chip temperature must not exceed 85C. If air is used as a coolant, h = 200W/m2. If a dielectric liquid is used as coolant, h = 3000W/m2. What is the difference in maximum allowable power through the chip between the two coolants? (answer in W) *

A square isothermal chip is of width 5mm on a side mounted in a substrate such that its side and back surfaces are well insulated, while the front surface is exposed to the flow of coolant at 15C. From reliability considerations, the chip temperature must not exceed 85C. If air is used as a coolant, h = 200W/m2. If a dielectric liquid is used as coolant, h = 3000W/m2. What is the difference in maximum allowable power through the chip between the two coolants? (answer in W) *

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

Water at a flow rate of 0.215 kg/s is cooled from 70°C to 30°C by passing it through a thin-walled tube of diameter of 50 mm and maintaining a coolant at 15°C in cross flow over the tube. What is the required tube length if the coolant is air and its velocity is V = 20 m/s?Water : cp = 4181 J/kg⋅K, μ = 548 × 10-6 N⋅s/m2, k = 0.643 W/m⋅K, Pr = 3.56.Air : ν = 15.89 × 10-6 m2/s, k = 0.0263 W/m⋅K, Pr = 0.707.(Hint: For external flow use Churchill/Bernstein correlation.)
Air (pressure 1 atm) enters a circular pipe 5 cm in diameter at 20 °C with an average speed of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the mean outlet temperature is 80°C. Estimate the length of the tube. Mainly, I also need the solution from concepts of how the heat flow behaves in the system, it can be with a diagram.
A non-thermally insulated industrial water vapor pipe is 25 m long and 100 mm in diameter. This line crosses a building whose walls and ambient air are at 25oC. Pressurized steam holds the tube surface at 150oC and the convective coefficient is 10 W/(m.K). The surface emissivity is ε=0.8. (a) the heat loss on this line; (b) if the steam is generated in a boiler that operates at 90% efficiency and uses natural gas priced at $0.20/MJ, what is the annual cost of this heat loss? Answer: (a) 18.41 W; (b) $129,000
For safety reasons, parts can be directly blown by air. with dimensions of 15 cmx20 cm, which are not allowed to contact printed circuit board, 20 cm long 0.2 opened inside Cold air from a rectangular hole of cmx14 cm will be cooled. from electronic parts The heat generated is transmitted from the thin layer of the card to the duct, where it is combined with the air entering the duct at a temperature of 15 °C. is removed. The heat flux on the upper surface of the channel can be considered uniform and The heat transfer from the surfaces can be neglected. If the velocity of the air in the duct does not exceed (590) m/min and the surface temperature of the duct is constant at 50 °C, this circuit board can be safely placed on it. Calculate the maximum total power of the electronic parts to be placed.
In the final stages of production, a pharmaceuticalis sterilized by heating it from 30°C to 75°C as it moves at0.2 m/s through a straight thin-walled stainless steeltube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrappedaround the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluidenters the tube with a fully developed velocity profile and a uniform temperature profile, what is thesurface temperature at the tube exit? Fluid properties may be approximated as ? = 1000 kg/m3, cp =4000 J/kg K, ? = 2 x 10-3 kg/s m, k = 0.8 W/m K, and Pr = 10.
A bare stainless-steel tube having an outside diameter of 76.2 mm and an ε of 0.55 is placed horizontally in the air at 294.2 K. The pipe surface temperature is 366.4 K. Calculate the value of hc + hr for convection plus radiation and the heat loss for 3 m of pipe.
A thick-walled cylindrical tubing of hard rubber (k=0.151 W/m*K) having an inside radius of 5 mm and an outside radius of 20 mm is being used as a temporary cooling coil in a bath. Ice water is flowing rapidly inside, and the inside wall temperature is 275 K. The outside surface temperature is 300 K. A total of 20 W must be removed from the bath by the cooling coil. How many meter of tubing are needed?
A vehicle carrying refrigeration box is moving with a speed of 24 m/s on a road withambient temperature of 323 K. The dimensions of box are 3 m(H) × 4 m (W) × 10 m (L).Assume a wall temperature of 283 K and air flow is parallel to the longest side of the box.Neglecting the heat loss from the front side and backside of the box, calculate heat lossfrom four surfaces. For flow over flat surfaces useNu = 0.036(Re)0.8(Pr)1/3The properties of air at bulk mean temperature are : = 1.165 kg/m3, Pr = 0.701, cp = 1005 J/kg – K,  = 16 × 10–6m2/s
2. Calculate the free convection heat transfer coefficient for a plate 6 ft high and 8 ft wide at 120 °F that is exposed to nitrogen at 60 °F. (see attached) 3. Constant Flux Application. Air at 1 atm and 300 °C is cooled as it flows at a velocity of 5.0 m/s through a tube with a diameter of 2.54 cm. Calculate the heat transfer coefficient if a constant heat flux condition is maintained at the wall and the wall temperature is 20 °C above the temperature along the entire length of the tube. (See attached)