an oil at average temperature of 100 F flows at 1.2 ft/s velocity 0.834in inside diameter horizontal tube. The tube is heated by uniform heat flux the average surface temperature is 120F. Determine the heat transfer coefficient, Then the rate of heat transfer per length of the heating tube. Please write assumptions and do a sketch

an oil at average temperature of 100 F flows at 1.2 ft/s velocity 0.834in inside diameter horizontal tube. The tube is heated by uniform heat flux the average surface temperature is 120F. Determine the heat transfer coefficient, Then the rate of heat transfer per length of the heating tube. Please write assumptions and do a sketch

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.3P: 6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the...

See similar textbooks

Similar questions

6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Engine oil flows through a 50 mm diameter tube at an average temperature of147°C. The flow velocity is 80 cm/s. Calculate the average heat transfer coefficient if the tube wall is maintained at a temperature of 200°C and it is 2 m long. Hint: Area can be assumed to be equal to the vertical projectiion of the tube , i.e. LD. Ans.: h = 377.36 W/m2.K . Draw an illustration. Note: use the formula on the picture
Water is flowing through a 25-mm diameter and 10-m long tube. The water enters the tube at 20\deg C with a mass flow rate of 0.2 kg/s. The outlet mean temperature is 60\deg C, and the tube surface temperature is maintained constant. Determine the hydrodynamic and thermal entry.lengths. Is the flow fully developed? What is the convective heat transfer coefficient inside the pipe?
The fluid flows at a speed of 0.4 m/s through a horizontally placed smooth pipe with a diameter of 20 mm and a length of 24 m and heats an environment at a temperature of 87 oC. Considering that the pipe surface temperature remains constant, inside the pipe; a) In case of water flow,b) In case of engine oil leakage Calculate the heat transfer coefficient and friction factor in the in-pipe flow and compare and interpret the results.
Engine oil flows through a 25-mm-diameter tube at a rate of 0.5 kg/s. The oil enters the tube at a temperature of 25°C, while the tube surface temperature is maintained at 100°C. (a) Determine the oil outlet temperature for a 5-m and for a 100-m long tube. For each case, compare the log mean temperature difference to the arithmetic mean temperature difference.
1.A 0.5 m pipe is flowing with water at temperatures of 30 ^o C and 40 ^o C. Calculate the maximum velocity under conditions A.Laminar B.Turbulent
Water at a flow rate of 1kg/s is flowing in a pipe of internal diameter 5 cm. If the inside pipe surface temperature is 90°C and mean bulk water temperature is 50°C, compute the convective heat-transfer coefficient. Estimate the convective heat.
Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced by half while the flow rate and the pipe length are held constant, how that will affect the Reynold number and pressure drop.
Water flows in a 3.5-cm-diameter pipe so that the Reynolds number based on diameter is 2000 (laminar flow is assumed). The average bulk temperature is 10°C. What would the heat transfer coefficient be in W/m2.°C for such a system if the tube wall was subjected to a constant heat flux and the velocity and temperature profiles were completely developed? Evaluate properties at bulk temperature.
Air at 1 atmosphere and a temperature of 60f enters 1/2-in. id tube with a velocity of 80 fps. The wall is maintained at a constant temperature of 210 by condensing steam. Fin the convective heat-transfer coefficient for this situation if the tube is 5ft long
Engine oil flows at a rate of 0.95 kg/s through a tube of 119 mm inside diameter and is heated from 293 to 327 K by condensing steam at 373 K. For the described case answer the following:i. Identify the type of flow and explain briefly about the flow with suitable assumptions & sketches.ii. Determine the inside heat transfer coefficient and rate of heat transfer per meter length of pipe for the identified flow pattern.