In the section of the circuit shown, the current I₂ = 1.00 A (Figure 1) Figure 2.5 A www R 1009 wwww < 1 of 1 > 12 How much current is flowing through the resistor R? Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) I₁ = Submit HA Value Part B Complete previous part(s) Provide Feedback Units ?

In the section of the circuit shown, the current I₂ = 1.00 A (Figure 1) Figure 2.5 A www R 1009 wwww < 1 of 1 > 12 How much current is flowing through the resistor R? Express your answer to three significant figures and include the appropriate units. ▸ View Available Hint(s) I₁ = Submit HA Value Part B Complete previous part(s) Provide Feedback Units ?

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter10: Direct-current Circuits

Section: Chapter Questions

Problem 94CP: Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is...

See similar textbooks

Similar questions

The emf devices in the circuits shown in Figure P29.28 are identical. a. Redraw circuit 1 in figure P29.28, including (and labeling) the current in each branch of the circuit. Apply the junction rule to write an equation in terms of the currents you have labeled. b. Repeat part (a) for circuit 2 in Figure P29.28. c. Simplify your equations if necessary, and compare your answers for each circuit. What can you say about the two circuits?
A person with body resistance between his hands of 1.00 k accidentally grasps the terminals of a 20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation. (b) If the internal resistance of the power supply is 2000 , what is the current through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low-re si stance devices? Explain your reasoning,
The power dissipated in a resistor is given by P = V2/R, which means power decreases if resistance increases. Yet this power is also given by P = I2R, which means power increases if resistance increases. Explain why there is no contradiction here.
(a) When the switch S in the circuit of Figure P28.14 is closed, will the equivalent resistance between points a and b increase or decrease? State your reasoning. (b) Assume the equivalent resistance drops by 50.0% when the switch is closed. Determine the value of R.
A person with body resistance between his hands of 10.0k accidentally grasps the terminals of a20.0-kV power supply. (Do NOT do this!) (a) Draw a circuit diagram to represent the situation, (b) If the internal resistance of the power supply is 2000 , what is thecurrent through his body? (c) What is the power dissipated in his body? (d) If the power supply is to be made safe by increasing its internal resistance, what should the internal resistance be for the maximum current in this situation to be 1.00 mA or less? (e) Will this modification compromise the effectiveness of the power supply for driving low- resistance devices? Explain your reasoning.
Consider the circuit below, (a) What is the initial current through resistor R2? when the switch is closed? (b) What is die current through resistor R2 when the capacitor is fully charged, long after die switch is closed? (c) What happens if the switch is opened after it has been closed for some rime? (d) If the switch has been closed for a time period long enough for the capacitor to become fully charged, and then the switch is opened, how long before the current through resistor R1 reaches half of its initial value?
An automobile starter motor has an equivalent resistance of 0.0500 and is supplied by a 12.0-V battery with a 0.0100- internal resistance, (a) What is thecurrent to the motor? (b) What voltage is applied to it? (c) What power is supplied to the motor? (d) Repeat these calculations for when the battery connections are corroded and add 0.0900 to the circuit. (Significant problems are caused by even small amounts of unwanted resistance in low-voltage, high-current applications.)
A 240-kV power transmission line carrying 5.00x102. A is hung from grounded metal towers by ceramic insulators, each having a 1.00x 109- resistance. Figure 21.51. (a) What is the resistance to ground of 100 of these insulators? (b) Calculate the power dissipated by 100 of them, (c) What fraction of the power carried by the line is this? Explicitly show how you follow the steps in the Problem-Solving Strategies for Series and Parallel Resistors.
The label on a battery-powered radio recommends the use of a rechargeable nickel-cadmium cell (nicads), although it has a 1.25-V emf, whereas an alkaline cell has a 1.58-V emf. The radio has a 3.20 resistance.(a) Draw a circuit diagram of the radio and its battery. Now, calculate the power delivered to the radio (b) when using a nicad cells, each having an internal resistance of 0.0400 , and (c) when using an alkaline cell, having an internal resistance of 0.200 . (d) Does this differenceseem significant, considering that the radio's effective resistance is lowered when its volume is aimed up?
A battery has some internal resistance. (i) Clan the potential difference across the terminals of the battery be equal to its emir (a) no (b) yes, if the battery is absorbing energy by electrical transmission (c) yes, if more than one wire is connected to each let initial (e) yes, if the current in the battery is zero (e) yes, with no special condition required. (ii) Can the terminal voltage exceed the emf? Choose your answer from the same possibilities as in part (i).
How would the value of each of the four following physical quantities change over time after the switch is closed? Explain why for each case in 1 or 2 sentences. (You may assume that the resistance of the batteries, the wires, and the switch are negligibly small for this question). a. The voltage across the capacitor, VCAP b. The voltage across the light bulb, VBULB c. The current through light bulb, IBULB d. VBULB + VCAP
Can you help with sub question 9a. 9b. 9c. 9a. What is the time constant for this circuit? 9b. What is the charge on the capacitor after the switch has been closed for t = 2.32×10-2 s? 9c. What is the current through the circuit after the switch has been closed for t = 2.32×10-2 s? 9d. What is the voltage across the capacitor after the switch has been closed for t = 2.32×10-2 s?