In the spring arrangement shown in the figure below, the displacement x is caused by the applied force f. Assuming the system is in static equilibrium when x = 0 and that the angle 0 is small, identify the equivalent spring constant ke for this arrangement, where f kex. Here, k, = 1000 N/m and k2 = 1500 N/m. k2 - L2→ ww

In the spring arrangement shown in the figure below, the displacement x is caused by the applied force f. Assuming the system is in static equilibrium when x = 0 and that the angle 0 is small, identify the equivalent spring constant ke for this arrangement, where f kex. Here, k, = 1000 N/m and k2 = 1500 N/m. k2 - L2→ ww

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.3P: The L-shaped arm ABCD shown in the figure lies in a vertical plane and pivots about a horizontal pin...

See similar textbooks

Similar questions

The inclined ladder AB supports a house painter (85 kg) at C and the weight iq = 40 K/m} of the ladder itself. Each ladder rail (t5= 4 mm) is supported by a shoe (ts= 5 mm) that is attached to the ladder rail by a bolt of diameter d = 8 mm
A bumping post at the end of a track in a railway yard has a spring constant k = 8.0 MN/m (see figure). The maximum possible displacement d or the end of the striking plate is 450 mm. What is the maximum velocity vmaxthat a railway car of weight W = 545 kN can have without damaging the bumping post when it strikes it?
A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
Solve the preceding problem if the collar has mass M = 80 kg, the height h = 0.5 m, the length L = 3.0 m, the cross-sectional area A = 350mm2. and the modulus of elasticity E = 170 GPa.
A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal aim AB (length b = 30 cm) and a vertical arm BC (length c = 20 cm) pivoted at point B. The pivot is attached to the outer frame BCD that stands on a laboratory bench. The position of the pointer at C is controlled by two parallel springs, each having a spring constant k = 3650 N/m. that are attached to a threaded rod. The pitch of the threads is p = 1.5 mm. If the weight is 65 N. how many revolutions of the nut are required to bring the pointer back to the mark?
A crane boom of mass 450 leg with its center of mass at C is stabilized by two cables AQ and BQ (Ae= 304 mm2 for each cable) as shown in the figure. A load P = 20 KN is supported at point D. The crane boom lies in the y-z plane. (a) Find the tension forces in each cable: TAQand TBQ(kN}. Neglect the mass of the cables, but include the mass of the boom in addition to load P. (b) Find the average stress (s) in each cable.
Two rigid bars are connected to each other by two linearly elastic springs. Before loads are applied, the lengths or the springs are such, that the bars are parallel and the springs are without stress. (a) Derive a formula for the displacement E4at point 4 when the load P is applied at joint 3 and moment PL is applied at joint 1. as shown in the figure part a. (Assume that the bars rotate through very small angles under the action of load P.) (b) Repeat part (a) if a rotational spring, kr= kL2, is now added at joint 6. What is the ratio of the deflection d4 in the figure part a to that in the figure part b ?
The L-shaped arm ABCD shown in the figure lies in a vertical plane and pivots about a horizontal pin at A. The arm has a constant cross-sectional area and total weight W. A vertical spring of stiffness k supports the arm at point B. (a) Obtain a formula for the elongation of the spring due to the weight of the arm. (b) Repeat part (a) if the pin support at A is moved to D.
A light spring of force constant k = 160 N/m rests vertically on the bottom of alarge beaker of water (see figure (a)).A 5.00-kg block of wood (density = 650 kg/m3) is connected to the spring, and the block–spring system is allowed to come to static equilibrium (see figure (b)).What is the elongation ΔL of the spring?Include a free-body diagram for the block.(Hint: Begin your derivation with equilibrium: “ΣF = 0”. The derivation is a little complex, so don’t give up, and don’t be tempted to calculate the numerical answer in pieces.)
As shown in the figure below, a uniform bar with mass m moves freely along a vertical tube at one end, suspended from a spring, and moving along a horizontal tube. At this time, find the equilibrium state, and find the stability of each. (When the spring constant is k and x=0, the spring is not deformed.)
A spring with squared and ground ends is used for a load and deflection of 1.2 kN and 20 mm, respectively, with a spring index of 4. The wire diameter is 6 mm and the modulus of rigidity is 84 GPa. Which of the following is the active number of turns of the spring?
2.2-8 The device shown in the figure consists of a spring-supported indicator ABC with a stiffness k = 800 N/m. The spring is located at a distance b = 150 mm from end A of the pinned indicator. The device is adjusted so that the indicator points to zero on the angular scale when no load P is applied. For a load P = 8 N, what distance x must this load act in order for the indicator to show a scale of 3°?