Consider four springs with the spring constants: k1 =20 lb/in., k2 = 50 lb/in., k3 = 100 lb/in., k4= 200 lb/in. 1 k1, k2, k3, and k4 are in parallel a. 18.9189 Ib/in. b. 370.0 lb/in. c. 11.7647 Ib/in. d. 300.0 lb/in.

Consider four springs with the spring constants: k1 =20 lb/in., k2 = 50 lb/in., k3 = 100 lb/in., k4= 200 lb/in. 1 k1, k2, k3, and k4 are in parallel a. 18.9189 Ib/in. b. 370.0 lb/in. c. 11.7647 Ib/in. d. 300.0 lb/in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the horizontal displacement of joint C. The length, L, of trusses AC, BC is 1,300 mm. The applied force at joint C, is 5.0 kN. The cross-sectional area of both trusses, A, is 360 mm2. The elastic modulus of truss AC, E1, is 135 GPa. The elastic modulus of truss BC, E2, is 150 GPa.
Two identical ball bearings Pand Qare operating at loads 30 kN and 45 kN respectively The ratio of the life of bearing P to the life of bearing Q is....
Give short answers to the below questions i. What is the same in each spring for a combination of springs in parallel? ii. In general, how is the equivalent stiffness of a combination of springs calculated? iii. What is the torsional stiffness of an annular steel shaft (G=80X109 N/m2) with a length of 2.5m, inner radius of 10cm and outer radius of 15cm? iv. What is the torsional stiffness of a solid aluminum shaft (G=40X109 N/m2) with a length of 1.8m and a radius of 25cm? v. Calculate the static deflection in a liner spring stiffness 4000N/m when a mass of 20kg is hanging from it.
The equivalent spring stiffness of an inclined spring whose k = 5 N/m and angle of inclination θ = 35° 3.355 N/m 4.095 N/m 5.867 N/m 4.511 N/m
two cylinders are connected to form a parallel cylinder actuatingsystem. Assume the bore and rod diameters of the left cylinder are 120 mm and 60 mm, respectively, and that those of the right cylinder are 100 mm and 50 mm. If the mass of the external loads to be driven by the left and right cylinders are 750 and 500 kg, respectively, and the back pressure in both rod-end chambers is 200 kPa, calculate the operating pressure of each cylinder for driving the loads. (Assume that the left cylinder requires 550 kPa for no-load extension and the right one requires 500 kPa.) If the supplying flow is 150 L ・ min−1, what are the extending velocities of those cylinders? Consider the friction and back pressure for the design Will those two cylinders extend simultaneously under the stated condition
A 2000 lb. shell is fired from a gun weighing 300 000 lb. If the muzzle velocity of the shell is 1500 fps. and the recoil of the gun is checked by a nest of springs having a modulus of 2000 lb. per inch, what is the maximum recoil distance.
Two helical coil springs are made from a steel bar radius of 20 mm. One spring has an outer and inner diameter of 10 cm and 6 cm respectively while the other one has a coil diameter of 12 cm. The springs have 20 turns each. What is the equivalent stiffness of the assembly if: a. the spring with the smaller coil diameter is placed inside the spring with the larger coil diameter; b. the spring with the smaller coil diameter is placed on top of the spring with the larger coil diameter. c. the spring rate equivalent at (a) is parallel with the spring rate equivalent at (b) d. the spring rate equivalent at (a) is in series with the spring rate equivalent at (b) e. the derived spring rate equivalent equation at (c) f. the derived spring rate equivalent equation at (d)
The spring constant of a helical compression spring depends on which property?
A uniform beam that 10-m long is being supported by two men, one man at each end. The weight of the beam. Is 100-N. If the first man supporting at the right side exert twice as much as the second man on the left, where must a 50-N motor be placed (measured from the first man) on top of the beam? Show complete solution.
Subject : - Mechanical Engineering A helical spring is provided with a rigid plate at each end.A bolt passes through the spring and the endplates. By turning the nut, the spring is compressed until the coils touch. The height of the unloaded spring is 600 mm, its mean coil diameter is 100 mm and the diameter of the spring wire is 28 mm. The spring has 18 coils. The diameter of the bolt is 25 mm and each plate is 25mm thick. Calculate the elongation of the bolt when the spring is fully compressed as well as the stress in the spring wire ( E = 200 GPa and G = 80 GPa )
Two steel springs arranged in series support a load P. The upper spring has 12 turns of 25 mm diameter wire on a mean radius of 100 mm. The lower spring consists of 10 turns of 20 mm diameter wire on a mean radius of 75 mm. Use G = 83 GPa. Which of the following most nearly gives the value of the total elongation of the assembly? Which of the following most nearly gives the equivalent spring constant of the assembly? Which of the following most nearly gives the maximum value of P if the allowable shearing stress is 200 MPa?
Three extension springs are hooked in series and supports a weight of 70 kg. One spring has a rate of 0.209 kg ∕mm and the other two have equal spring rate of 0.643 kg ∕mm. Find the deflection.