Answered: A cylinder of internal diameter 3.5 m…

Name: A cylinder of internal diameter 3.5 m andthickness 7 cm contains a ga
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A cylinder of internal diameter 3.5 m andthickness 7 cm contains a gas. If the tensilestress in the material is not to exceed 70 N/mm, determine the internal pressure of thegas.

Engineering

Mechanical Engineering

A cylinder of internal diameter 3.5 m and thickness 7 cm contains a gas. If the tensile stress in the material is not to exceed 70 N/ mm-, determine the internal pressure of the gas.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.121P: One side of the container has a 03-m square door that is hinged at its top edge. If the container is...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 5 kg and a cross-sectional area of 35 cm2. A compressed spring above the piston exerts a force of 75 N on the piston. If the atmospheric pressure is 95 kPa, determine the pressure inside the cylinde
A gas is contained in a vertical, frictionless piston– cylinder device. The piston has a mass of 3.2 kg and a crosssectional area of 35 cm2 . A compressed spring above the piston exerts a force of 150 N on the piston. If the atmospheric pressure is 95 kPa, determine the pressure inside the cylinder.
An experiment was conducted using a communicating vessel to knowthehydraulic pressure. The communicating vessel consists of two column, XandY. Column X has a diameter of 15 cm and column Y of 75 cm. Oil (s = 0.852) wasfilled to the communicating vessel. A load of 1275 N was given to the columnY. Determine the minimum force that should be given to column Xso that theload can be lifted and the density of oil !
A roller with a diameter of D=84 cm, unit width up to a quarter of the volume was filled with methanol and immersed in water. Determine the mass of the roller if the height of the roller above the water is h=21 cm.
Determine the pressure at the interface of liquids of an open tank containing 3 m of oil (SG=0.79) and 10 cm of mercury (13.6)
A 20-cm-diameter vertical cylindrical vessel is rotated about its vertical axis at a constant angular velocity of 70 rad/s. If the pressure at the midpoint of the inner top surface is atmospheric pressure like the outer surface, determine the total upward force acting upon the entire top surface inside the cylinder.
Determine the distance (h) in mm ,that a column of mercury in the tube will be depressed when the tube is inserted into the mercury at a room temperature of 20°C. Set ( D= 6 ) mm , density of mercury =13550 Kg/m3 , (s) surface tension 37.5x10-2 N/m , a= 57 o 2- The Value of (h) is equal to .....?
A room in the lower level of a cruise ship has a 40-cm-diameter circular window. If the midpoint of the window is 2 m below the water surface, determine the hydro static force acting on the window, and the pressure center. Take the specific gravity of seawater to be 1.025
The distance between the centers of the two arms of a U-tube open to the atmosphere is 30 cm, and the U-tube contains 20-cm-high alcohol in both arms. Now the U-tube is rotated about the left arm at 3.5 rad/s. Determine the elevation difference between the fluid surfaces in the two arms.
A circular plate 3.0 m diameter is immersed in water in such a way that the plane of the plate makes an angle of 60 degrees with the free surface of water. Determine the position of the center of pressure from the free surface when the upper edge of the plate is 2 m below the free water surface.
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.