The answers your expert provided 30 minutes ago were not correct.Please try again.I Need correct Answers, I am begging you! LetI, = 25230°A,Vs = 302- 20°V,Z1 = 55+ j902,R2 = 902, R3 = 852, X2 = -402, N1 = 3, and N2 = 1. Com-pute the complex power received by Z1 and the phasor currents I2and I3.%3DN1:N2 I2中R2R3VsjX2+S1 =L.°VAI22 =.__°AI3 =_L__°A

Complex Power can be explained as the representation of electrical power in form of complex number.

Is = 25230°A, R2 = 902, R3 = 852, X2 = -402, N1 = 3, and N2 = 1. Com- Let Vs = 302 – 20°V, Z1 = 55+ j902, %3D %3D %3D %3D %3D pute the complex power received by Z1 and the phasor currents 2 and I3. N;:N2 I2 R2 R3 I, jX Si =L °VA I3 °A

Is = 25230°A, R2 = 902, R3 = 852, X2 = -402, N1 = 3, and N2 = 1. Com- Let Vs = 302 – 20°V, Z1 = 55+ j902, %3D %3D %3D %3D %3D pute the complex power received by Z1 and the phasor currents 2 and I3. N;:N2 I2 R2 R3 I, jX Si =L °VA I3 °A

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2P: Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your...

See similar textbooks

Related questions

Q: R V = 12 V, V1 = 6 V Determine the maximum output voltage O 18 V O ov O 6V O 30 V

Q: P5.63. Consider the circuit shown in Figure P5.63. Find the phasor current I. Find the power,…

A: Ac sinusoidal analysis Given Inductor value = 1H

Q: 4. A signal with power 7 mW is distorted by noise with power 0.002 mW. What is the signal to noise…

A: In this question, We need to determine the SNR in the dB We know SNR is the ratio of signal power…

Q: Problem 1 The unbalanced A-load of Fig. 1 is supplied by balanced line-to-line voltages of 240 V in…

A: In this question we need to find a line current of the given three phase delta connected circuit.

Q: A certain op-amp has bias currents of 50µA and 49.3µA. The input offset * current is (a) 700 nA O…

Q: Which of the following is a Load and Resistance Design Concept? Service load Rn/2 Factored load O…

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: of 0,0242 per phase and standstill etermine the speed at which maximum torque is developed. Ans[1440…

Q: 1) Express point P(-2, 6, 3) in cylindrical and spherical coordinates. 2) Express vector A = 2.467a,…

Q: CTICE PRU Determine the Fourier series of the sawtooth waveform in Fig. 16.9. CHAPTER 16 The Fourier…

A: We need to find Fourier series coefficient for given waveform

Q: 1- How does a diode work as a voltage regulator? 2- What is a Zener preakdown? 3- What happens to…

A: When the zener diode is reverse biased it works as a voltage regulator It's a semiconductor diode It…

Q: 80 2 I, j60 2 20 Ω ww ell 100/120° V -j40 2 -j40 2 60 30° V

Q: 4. Determine the current passing through the 7K ohm resistor 1k 2k 5V 3k -7k

Q: Assume a conductor, H=5pa, A/m. (a)! curface 0<p<4, 0<o<2a, z = 0. (

A: Given H=5ρaϕ A/m

Q: torque. Ans[40.5 N.m, 63.6 N.m, 1333r.p.m] The resistance and standstill reactance of each phase of…

Q: Use nodal method to find the branch currents l1, 12, l3, 14 and Is in the network shown below.

A: We need to find the branch currents I1, I2, I3, I4, and I5.

Q: Design a clamper circuit with the below waveform: -4 V -36 V

Q: electronics circuit determine the following: - If Q1 is turned on in Figure 4a, what is Vout?…

Q: - Use superposition to obtain vx

Q: A memory IC that can hold up to 1024 bits and has a 8 address lines can be organized into…

A: Answer: 256x4 a). It is not a valid option. 1024x1 requires 10 address lines. 210 = 1024. b) a).…

Q: A total current of 60 A is divided among 3 parallel branches having resistances of 10, 6, and 12…

A: It is given that a total current is divided among three parallel branches of resistance 10, 6 and 12…

Q: Homework: Q1) For the circuit shown in Fig. 1, find the current I30 and the average power. Let v(t)…

Q: D1 Vsecondary Vfiltered D2 V1 sine Rload I 120 VAC @ 60 Hz D3 10:1 - D4 Figure 1: Bridge Rectifier…

A: We need to find out capacitor value for given filter voltage

Q: s Explain the meaning of the following sentence, use an example to clarify your answer: "The…

A: It is given that: VC0-=5V

Q: Find the Re(z) and Im(z) z=cosh[(3+i2)(1+i)]

A: The solution is given below

Q: What is Kelvin probe force microscopy (KPFM). How does it work and what information can be obtained…

Q: Example 1: Calculate the percent voltage regulation for a three-phase wye-connected 2500 kVA 6600-V…

Q: 12 R VR ILmax V() -Us tVR t Ve Ves Kー 3- 0-U es Figure 6: An RL circuit with R = 12 N, L = 48 µH,…

Q: Determine the charge in capacitor C5. 6F 3F 6F C, 12 F 6F 12 volt

A: In this question we will find charge in capacitor C5....

Q: In the circuit above:, the supply provides 3 V, the resistor is 1.66 kN, and the inductor is 13 mH.…

A: The solution is given below This is a basic problem of RLC series circuit

Q: In the balanced three-phase Y-A system shown, find the line current I and the average power…

Q: Wien Bridge Oscillator - Calculate the conditions (K and frequency) for oscillation for this…

Q: Use cascading to design a Butterworth active low pass filter with the following specifications: Amax…

A: According to the question, We need to design, Butterworth active low pass filter.

Q: Line Current (i) ii) Line voltagel iii) Power factor of the circuit

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Question 2: Component values of the following circuit are listed in the Table I. Switch opens at…

A: In this question, Find the expression of the output voltage Vo as shown in the circuit. We know…

Q: If a load draws 15 mA from a 9 V battery, what power (in W to two sig. figs.) does the load draw

A: In this question, We need to calculate the power? If a load draws 15 mA from a 9 V battery.

Q: Q2: A three-phase Transmission line with 1,956 cm diameter conductor, the corona takes place if the…

A: Given data : Disruptive Voltage, Vc=210 kV= 210000 VDiameter,d= 1956 cm =19.56 mr= d2=19562=978…

Q: Find the electrical current I. The voltage in every resistor of the circuit. The voltage in the…

A: Given circuit:

Q: Q10. A 50 Hz synchronous generator having an internal voltage 1.2 pu, H = 5.2 MJ/MVA and a reactance…

Q: Q2. A 0.5 µF capacitor has a periodic voltage as shown in Figure Q2. Determine and plot as a…

A: In this question, Voltage waveform across the capacitor is given We need to draw the current in the…

Q: Questions Q1) what is meant by Insolation, ARC in solar systems?

Q: S1= 3020° Amperes S2 = 220 20° Volts USE MESH ANALYSIS to get: а. 11, 12, 13, b. lo c. V3 and P3…

A: The figure is as shown below, We need to find I1, I2, I3, Io, V3, and P3.

Q: For the transistor circuit a. what is VCE when VIN= 0 V? b. What minimum value of Ig is required to…

A: The transistor circuit is shown below: a. The collector-emitter voltage is calculated as:…

Q: Component values of the following circuit are listed in the Table I. Answer the following questions…

A: In this question, We need to determine the value of voltage V2 as shown in the circuit . We are…

Q: P5.43. Compute the complex impedance of the net- work shown in Figure P5.43 for w = 500. 1000 and o…

Q: What is the capacitive reactance at 4 MHz for a 10 nF capacitor?

Q: Sketch the final waveform of below circuit. * V1 D2 9V R1 25V

Q: 2. A silicon one sided abrupt p* /n junction has Na = 1019 cm and Ng =ND = 3 x1015 cm³. Critical…

A: We know width of depletion region isw=2εVo+VBq1NA+1NDSince Vbi<<VB,…

Q: In the circuit above:, the supply provides 3 V, the resistor is 1.66 kN, and the inductor is 13 mH.…

A: The solution is given below

Q: An Autotransformer designed for 4,000/2,300 volt operation supplies a load of 32Kw at a power factor…

A: In this question we need to find a transformed power of the given auto transformer.

Q: 3002 4.5/0 A 4009 25 Vx 0.0125V 20020 V Vx 1002 3302 5002

Concept explainers

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors. The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.

Question

The answers your expert provided 30 minutes ago were not correct.

Please try again.

I Need correct Answers, I am begging you!

Let
I, = 25230°A,
Vs = 302- 20°V,
Z1 = 55+ j902,
R2 = 902, R3 = 852, X2 = -402, N1 = 3, and N2 = 1. Com-
pute the complex power received by Z1 and the phasor currents I2
and I3.
%3D
N1:N2 I2
中
R2
R3
Vs
jX2
+
S1 =L.
°VA
I2
2 =.
__°A
I3 =_L__°A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose that v1(t) = 90 cos(ωt-15) and v2(t) = 50 sin (ωt-60). Use phasors to reduce the difference vs(t) = v1(t) –v2(t) to a single term of the form Vmcos(ωt+θ). State the phase relationships between each pair of these phasors.
Suppose that v1(t)=100 cos(ωt+45°) and v2(t)=150 sin(ωt+60°). Use phasors to reduce the sum vs(t) = v1(t) +v2(t) to a single term of the form Vm cos(ωt+θ). Draw a phasor diagram showing V1, V2 and Vs. State the phase relationships between each pair of these phasors.
Solve the power triangle at Z6 in the circuit diagram below.V1, V2, and V3 = 220∠0°, 50 HzZ1 = 7+j8 ohmsZ2 = 6+j3 ohmsZ3 = 5+j5 ohmsZ4 = 2+j3 ohmsZ5 = 8+j4 ohmsZ6 = 1+j9 ohms
Find the phase angle between i1 = -4 sin (377t + 55) and i2 = 5 cos (377t - 65). Indicate whether i1 is leading or lagging behind i2. And also, if v1 = -10 sin (ωt - 30) V and v2 = 20 cos (ωt + 45) V, find v1 + v2.
If Vbc = Vxy, which of the given for the circuit below is correct? A) The Vab phasor is 90 degrees back from the Vyz phasor. B) The is phasor is in phase with the i2 phasor. C) The i1 phasor is 90 degrees back from the i2 phasor. D) The Vac phasor is in phase 90 degrees ahead of the Vxz phasor.
Between i1 = -30cos(ωt + 50°) and v1 = 24sin(ωt - 10°), calculate the phase angle. Sketch and state which sinusoid is leading.
Suppose that v1(t)=100 cos(ωt) and v2(t)=100 sin(ωt). Use phasors to reduce the sum vs(t) = v1(t) + v2(t) to a single term of the form Vm cos(ωt+θ). Draw a phasor diagram, showing V1, V2 and Vs .State the phase relationships between each pair of these phasors.
Find out the zero-phase sequence components of the following set of three unbalanced voltage vectors: Va =10cis30° ,Vb= 30cis-60°, Vc=15cis145°" (THOS PROBLEM IS MULTIPLE CHOICE PLEASEE CHOOSE THE LETTER WITH THE CORRECT ANSWER AND PLEASE PROVIDE YOUR CLEAR SOLUTION! A 16.809cis-72.579° B 5.603cis72.579° C 16.809cis-47.421° D 5.603cis-47.421°
The signal V1=100 cos(500t - 30°) and the signal V2=20 sin (500t +45°) compared in phase would be a) V1 15° ahead of V2 b) V1 75° behind V2 c) V2 15° ahead of V1 d) None of the above
What is the phasor representation of I(t)=I∘cos(ωt) at half-period? Explain. A.← B.↑ C.→ D.↗The links below show different answers. Defend yours.a. https://www.bartleby.com/questions-and-answers/what-is-the-phasor-representation-ofiticoswtat-half-period/970f7f4b-f43d-4ff2-9be5-0e61b7f4ffebb. https://www.bartleby.com/questions-and-answers/what-is-the-phasor-representation-of-it-coswt-at-half-period-o-a.-o-b.-o-c.-o-d.-x/8240eeab-f494-45d9-90b0-17809c847a75c. https://www.bartleby.com/questions-and-answers/what-is-the-phasor-representation-of-iticoswt-at-half-period-a.-b.-c.-d./47f627d0-8180-42a7-9186-2ce88402dcd9
Solve the power triangle at Z6 using the following network law below.1.) Kirchoff's LawGiven:V1, V2, and V3 = 220∠0° V, 50 HzZ1 = 7+j8 ohmsZ2 = 6+j3 ohmsZ3 = 5+j5 ohmsZ4 = 2+j3 ohmsZ5 = 8+j4 ohmsZ6 = 1+j9 ohms
Solve the power triangle at Z3 using the following network law below. Thanks in advance!!!3.) Nodal AnalysisGiven:V1, V2, and V3 = 200∠0° V, 60 HzZ1 = 3+j5 ohmsZ2 = 4+j7 ohmsZ3 = 8+j6 ohmsZ4 = 5+j10 ohmsZ5 = 7+j8 ohms