is low-alloy steel oxidation resistant? if yes, then why?

Q: how does iron and aluminum in terms of their property resist corrosion.

A: Iron and aluminium having different chemical properties when they come in contact with water and…

Q: Which of these cast iron would allow the greatest amount of plastic deformation before fracture .…

A: Nodular cast iron has highest tensile strength of about 70ksi followed by grey cast iron with 50ksi…

Q: Determine the welding zone classification of A36 and A922 steel.

A: The hardness of the steel is related to the welding of steel. The welding of harder steels is…

Q: Why Ceramics are stronger in compression than in tension

A: The properties of ceramic Material:   Ceramics is a rigid and brittle material and is not capable…

Q: Discuss the main methods used to protect steel from corrosion.

A: The corrosion of steel is caused due to the electrochemical reaction that takes place in the…

Q: What is the most important heat treatment for hardening steels?

A: Brief Concept Introduction- Hardening of steels- Steels are heated at the proper temperature for…

Q: Sketch the stress–strain behavior of steel, and identify different levels of strength. What is a…

A: It is required to draw the stress strain curve for steel.

Q: A. Which material is considered as ductile and which one is considered as brittle? Explain. What is…

A: Part A) Material A has a typical ultimate stress point and breaking stress point, along with a clear…

Q: 5.) List one application and one property of the following alloy steels: (i) Stainless Steel; (ii)…

A: To write property and uses of stainless steel and high speed steel

Q: A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250 MPa.…

A: Calculate the modulus of resilience modulus of resilience=σ22Ehere σ is stress or yield strength, E…

Q: Why does the iron–carbon phase diagram go only to 6.7% carbon?

A: The iron-carbon phase diagram is shown below,

Q: Answer the following questions for these TWO type of metals, (i) Steel 1050, and (i) aluminium…

A: Solution for Subpart b – For Steel 1050, the approximate ultimate tensile strength is fu = 690 MPa.…

Q: Explain stress-strain relationship for mild steel. Discuss in brief about the elastoplastic…

A:

Q: 90 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000…

A: Given data stress= 200 MPa rupture lifetime be 509 h

Q: Why is coil steel used for cold-formed steel fabrication annealed prior toshaping?

A: The coil of steel is used for cold-formed steel fabrication annealed prior to shaping beacse,

Q: What type of atomic bonding characterizes the ceramics?

A: Ceramics- It is a material which is non-metallic or inorganic in nature. Ceramics are generally…

Q: which one of the following processes causes a dramatic increase in the hardness of a steel part? A…

A: Option -A - Quenching is the correct answer  Quenching is the process of soaking metal at very high…

Q: Why should stainless steel not be held at temperatures between 800°F and 1500°f?

A: Stainless steel should not be held at temperatures between 800°F and 1500°F as in this range of…

Q: Give me right solution  A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum…

A:

Q: What are the properties of graphite that allow it to be useful in a lead pencil, and how does the…

A: Pencils contain a form of solid carbon known as graphite. The "graphite" name basically derived from…

Q: A structure is designed as a horizontal cantilever beam, of circular cross-section, and length 1 m.…

A: step 1-

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: Assume that 100 kN load is applied. Then using equilibrium and compatibility equation the load…

Q: What is the difference between steel and GFRP in terms of properties? Find out about the current use…

A: The question deals with the difference between steel and GFRP in terms of properties and the current…

Q: Is a steel a heterogeneous or homogeneous mixture?

A: Heterogeneous :-                     Heterogeneous mixture is a mixture of two or more compounds.…

Q: Explain briefly what is a low carbon steel, medium carbon steel, and high carbon steel  and specify…

A: Low carbon steel: Low carbon steel is defined as steel with a carbon content of up to 0.25%. Medium…

Q: Provide a general description of crucible furnace used in Industrial Manufacturing of Steel.

A: Manufacturing is the process of transforming raw materials or parts into completed things using…

Q: 44. Which of the below is not an example of a base? A. O White lead В. О Cobalt C. O Zinc oxide D. O…

A: Which of the below is not example of base

Q: A combined section of steel and copper is subjected to a compressive load. Refer to the table below…

A: We will calculate stress using maximum strain.

Q: Question 3 For a 40 wt% Sn-60 wt% Pb alloy at 150 °C and taking the densities of Pb and Sn at 150 °C…

A: The mass fraction of a particle is the ratio of the mass of that particle to the total mass of the…

Q: Determine the welding zone classification of A36/A36M and A922/A922M steel.

A: The zones serve as a guide for establishing how to calculate requirements of preheat .

Q: Consider an 6061-T6 aluminun alloy having an elastic modulus of 75 GPa and yield strength of 260…

A: Given data- Elastic modulus (E)=75 GPa=75×103 MPa Yield strength (σy)=260 MPa