Give me right solution A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum allowable deflection must not exceed 0.28 inches. What is the required area based on maximum allowable deformation? (in2)

Give me right solution A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum allowable deflection must not exceed 0.28 inches. What is the required area based on maximum allowable deformation? (in2)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.2DP

See similar textbooks

Related questions

Q: A rectangular steel bar 0.5 inch thickness by 1.5 inches width and 220 ft long is subjected to a…

Q: Please help me with this one. Please use the second photo as reference. Question: Solve for Vmax…

A: To find maximum shear and maximum moment

Q: Tensile test had made to cylinder shape with diameter 3.0 In and length 5.7 In It had maximum…

A: proof stress- proof stress is define for those ductile metal in which yield point is not very clear…

Q: What is the angle of twist for a solid aluminum bar 100 mm diameter subjected to a 10 kN-m. The bar…

A: Length of Aluminum Bar = 3m Torque applied = 10kN-m G = 80GPa = 80000 MPa Diameter of bar = 100mm…

Q: An aluminum right-circular cylinder surrounds a steel cylinder as shown in Fig. 1-29. The axial…

Q: Note: Replace all zero digits of your ID number by number "2" Problem #1: XN Use X Last 3 digits of…

Q: 0.20 cm 0.20 cm 3 cm 0.25 cm

Q: Rod AB is made of a mild steel that is assumed to be elastoplastic with E = 200 GPa and oy =250MPA .…

A: Soln⇒E=200 Gpaδy=250 MpadAB= 9 mm.LAB 1=1.25 m.Yield stress in AB(δy)=PAA=π4×92 ⇒ 63.67…

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the…

A: Given E= 70Gpa= 70000Mpa

Q: A compound bar consists of (4) aluminum alloy bars of (2mm) diameter and (2) steel bars of (3mm)…

A: Thermal Stress : The stress produced by change in temperature in a material is known as thermal…

Q: SEATWORK The figure as shown, ADD the last 2 digits of your i.d. number in the load P. Student i.d.…

A: Determine load for every P in three case

Q: A sheet of aluminum is stretched in the xy-plane. If the strains in the sheet are ϵx = 0.3 x10-3 and…

A: Given: x-direction strain = 0.3 x 10-3 y-direction strain = 0.25 x 10-3 Modulus of elasticity = 110…

Q: An aluminum rod has a cross-sectional area of 0.19635 in2. An axial tensile load of 6000 lb. causes…

A: Given: Cross section area of rod = 0.19635 in2, Tensile load = 6000 lb

Q: Please show your solutions. Thank you!

Q: A test piece is cut from a brass bar and subjected to a tensile test. With a load of 6.4 kN the test…

A: A. (1) The stress in the bar is given by: σ=LoadArea Given data, Load = 6.4 kN Area =…

Q: Hooks and héáds sháll nót bé used tó develop bars in compression.

A: Above statement is TRUE. heads and hooks shall not be used to develop bar in compression.

Q: Q2\ A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in…

A: When the deviation exceeds the maximum allowable value, the amount of radiation obtained on the…

Q: A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. NOTE:…

Q: 9. Determine the cracking moment for the beam section shown. The bars are each 32mm in diameter. Use…

A: fc = 21 MPa

Q: 1. Titanium alloy with an elastic modulus of 107 GPa (15.5 x 106 psi) and an initial diameter of 3.8…

Q: AN ALUMINUM SEGMENTS HAVING A DIAMETER AND LENGTHS SHOWN IN THE FIGURE. IF E = 85 KPa, COMPUTE THE…

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: An SAE3140 OQT 1300 steel bar with a rectangular cross section of 2 in ( base) by 3.5 in (height)…

A: From table Design Properties of Carbon and Alloy Steels (appendix 3 ) For SAE3140 OQT 1300…

Q: bolts evenly spaced around a bolt circle 12 in. in diameter, and six 4 -in. aluminum bolts on a…

A: To find the torque (T)-

Q: A rigid beam rest on two bronze bars 700mm long. Another aluminum bar is placed between them which…

A: The FBD of the given beam is shown below: For the aluminum bar to take load the displacement in…

Q: The composite bar as shown is placed between two rigid walls. At 30°C, there is a gap of 0.2mm…

Q: A Aluminum L = 3 ft A = 0.75 in.² E = 10 x 106 psi 2ft 3 ft. с B Bronze L = 4 ft A = 0.25 in.² E =…

Q: 7. ASTM suggests a tolerance of .. water. A. 12 percent to allow the variation in strength as a test…

A: ASTM suggest a tolerance of 8% to allow the variation in strength as a test of water. It means if we…

Q: Q:-A simply supported beam given below is prestressed by 1500 KN force. Modulas of rupture of…

A: Cracking moment denoted as (M cr ) is defined as the moment, which when exceeded causes the cracking…

Q: Calculate the absolute maximum stress in the steel in MPa. d. Calculate the stress in the steel…

Q: A structure is designed as a horizontal cantilever beam, of circular cross-section, and length 1 m.…

A: step 1-

Q: Complete Table P4.2. For a member where a deflection criterion controls,which material would require…

A: For A36 steel, the values of yield strength, ultimate strength and modulus of elasticity are 36 ksi,…

Q: 7. ASTM suggests a tolerance of .... percent to allow the variation in strength as a test of water.…

Q: Beam and load cases Maximum Beam Deflection PL³ dmax 3EI

A: To find maximum deflection of cantilever beam

Q: 3. An ASTM A36 structural steel beam 5.00 m long is placed between two rigid supports. When the…

A: Given data, ASTM A36 steel Length of beam = 5 m Initial temperature = 20° C Final temperature = 45…

Q: 1. The assembly has the diameters and material makeup indicated. If it fits securely between its…

A: αal=12.8×10-6/°Fαbr=9.6×10-6/°Fαst=9.6×10-6/°FEal=10.6×106 lb/inEbr=15×106 lb/inEst=128×106 lb/in

Q: A copper cylinder 150mm outside diameter has walls 25mm thick. End plates are stayed by a 25mm…

Q: Which of the following diameter of Grade 60 reinforcing bar can withstand a tensile load of 210 000…

Q: Estimate the cross-sectional area of a 350S125-27 cold-formed shape.a. If the member is tested in…

A: Given: The yield strength is 33 ksi.

Q: 24 Tensile test well done with standard tensile test spaceman with diameter 25 mm & length 120 mm…

A: The given data is shown below: Diameter=25 mmLength=120 mm

Q: An aluminum right-circular cylinder surrounds a steel cylinder as shown. The axial compressive load…

A: ANSWER:-

Q: tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of…

Q: A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is…

A: Given :

Q: A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the…

Q: A wood beam is strengthened using two steel plates as shown in the figure below. 1 6 mm A 150 mm 6…

Q: Consider the timber beam shown below. The beam is made out of southern yellow pine, with an…

A: Given :

Q: The compound bar containing steel bronze and aluminum segments carries the axial loads shown in the…

A: The compound bar is made of two metals of unequal coefficients of expansion, welded together. It…

Concept explainers

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.

Question

Give me right solution

A steel bar that is 28 feet long is subjected to a 251 kip load. Maximum allowable deflection must not exceed 0.28 inches. What is the required area based on maximum allowable deformation? (in²)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis and procedures for material selection

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter of 1 2 inch. The gage length (the length over which the elongation is measured) is 2 inches. For a load 13.5 kips, the elongation was 4.6610 3 inches. If the load is assumed to be within the linear elastic rang: of the material, determine the modulus of elasticity.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded
An aluminum rod has a cross-sectional area of 0.19635 in2. An axial tensile load of 6000 lb. causes the rod to stretch along its length, and shrink across its diameter. What is the diameter before and after loading? answers in inches. complete solution with fbd
Show complete process. A tensile load of 150 kN is applied to a round metal bar with a diameter of 16 mm and a gage length of 80 mm. Under this load the bar elastically deforms so that the gage length increases to 80.1192 mm and the diameter decreases to 15.89 mm. Determine the modulus of elasticity (in MPa) and Poisson’s ratio for this metal.
A threaded round steel bar is subjected to a tota axial pull of 8000 lb. If the diameter of the unthreaded portion is 7/8 in., the unit stress in that portion is A. 10,470 psi B. 13,310 psi C. 16,230 psi D. 19,880 psi
topic: mechanics of deformable bodies A steel tube with 3cm outside diameter, 0.25cm thick, and 4m long is covered and lined throughout with copper tubes 0.20cm thick. The three tubes are joined together at their ends. What is the maximum compressive load that can be applied to the top such that the total deformation does not exceed 0.50mm? Esteel = 200 GPa & Ecopper = 110 GPa. a.12.64 kN b.15.90 kN c.20.87 kN d.36 kN e.11.50 kN f.10.15 kN g.9.20 kN h.18.22 kN i.4.44 kN j.8.78 kN
A cylindrical rod of steel (E = 207 GPa),4mm in diameter is to be deformed by atensile force. Determine the force (in N)that will produce an elastic reduction of2.5 x 10-3mm in diameter if Poisson’sratio is 0.30. Show complete solution and formulas used.
A drill rod with a diameter of 1/2 in. is made of high-strength steel alloy with a shear modulus of 11.6 * 106 psi. The rod is to be subjected to a torque T.What is the minimum required length L of the rod so that the cross section at one end can be rotated 60° with respect to the other end without exceeding an allowable shear stress of 45 * 103 psi?
1/ Calculate maximum deflection of the beams 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Spronze=80 MPa, find the maximum weight of the beam that the system can support (in KN). note: please help us in this sample question and it is not a graded question but a practice question thank you
Tensile test had made to cylinder shape with diameter 3.0 In and length 5.7 InIt had maximum elastic was under load at (128425x10-2) Iband deformed with 6.2 In length and 2.85 In diameter.This is correspond 0.2 percent yield point.Compute modulus of elasticity (ib/in2)