It is desired to heat the workshop with a stove made of falling cylindrical sheet material with an outer diameter of 400 mm and a height of 1600 mm. The surface temperature of the stove is 217 oC and the radiation emission coefficient is 0.92, the temperature of the workshop surfaces is 12 oC and the ambient temperature of the workshop is 17 oC. Next to the stove, the workshop surface area is very large. From the side surface of the stove to the workshop; a) By transport, b) with radiation Calculate the heat transfer.

It is desired to heat the workshop with a stove made of falling cylindrical sheet material with an outer diameter of 400 mm and a height of 1600 mm. The surface temperature of the stove is 217 oC and the radiation emission coefficient is 0.92, the temperature of the workshop surfaces is 12 oC and the ambient temperature of the workshop is 17 oC. Next to the stove, the workshop surface area is very large. From the side surface of the stove to the workshop; a) By transport, b) with radiation Calculate the heat transfer.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter11: Heat Transfer By Radiation

Section: Chapter Questions

Problem 11.35P

See similar textbooks

Similar questions

Three thin sheets of polished aluminum are placed parallel to each other so that the distance between them is very small compared to the size of the sheets. If one of the outer sheets is at 280C and the other outer sheet is at 60C, calculate the temperature of the intermediate sheet and the net rate of heat flow by radiation. Convection can be ignored.
1.13 If the outer air temperature in Problem is –2°C, calculate the convection heat transfer coefficient between the outer surface of the window and the air, assuming radiation is negligible.
8.15 A mercury bath at is to be heated by immersing cylindrical electric heating rods, each 20 cm tall and 2 cm in diameter. Calculate the maximum electric power rating of a typical rod if its maximum surface temperature is .
A horizontal, 3-mm-thick flat-copper plate, 1-m long and 0.5-m wide, is exposed in air at 27C to radiation from the sun. If the total rate of solar radiation absorbed is 300 W and the combined radiation and convection heat transfer coefficients on the upper and lower surfaces are 20 and 15W/m2K, respectively, determine the equilibrium temperature of the plate.
1.11 Calculate the heat loss through a glass window 7-mm thick if the inner surface temperature is 20°C and the outer surface temperature is 17°C. Comment on the possible effect of radiation on your answer.
A long wire 0.7 mm in diameter with an emissivity of 0.9 is placed in a large quiescent air space at 270 K. If the wire is at 800 K, calculate the net rate of heat loss. Discuss your assumptions.
A spherical communications satellite, 2 m in diameter, is placed in orbit around the earth. The satellite generates 1000 W of internal power from a small nuclear generator. If the surface of the satellite has an emittance of 0.3, and is shaded from solar radiation by the earth, estimate its surface temperature.
An astronaut performing an extra-vehicular activity(space walk) shaded from the Sun is wearing a spacesuitthat can be approximated as perfectly white (e = 0) exceptfor a 5 cm × 8 cm patch in the form of the astronaut’snational flag. The patch has emissivity 0.300. The spacesuitunder the patch is 0.500 cm thick, with a thermalconductivity k = 0.0600 W/m °C , and its inner surface isat a temperature of 20.0 °C . What is the temperature of thepatch, and what is the rate of heat loss through it? Assumethe patch is so thin that its outer surface is at the sametemperature as the outer surface of the spacesuit under it.Also assume the temperature of outer space is 0 K. You willget an equation that is very hard to solve in closed form,so you can solve it numerically with a graphing calculator,with software, or even by trial and error with a calculator.