Dynamic Q6) The distance R in (m) is:a. 77.08O b. 156.03O c. 103.18O d. 88.24O e. 124.22Q7) The vertical component of the velocity(downward) of skier at B in (m/s) is:a. 42.09O b. 30.79c. 40.74O d. 77.15O e. 53.59 It is observed that the skier leaves the rampA at an angle 0A = 30 degrees with thehorizontal and a velocity VA =21.8 m/s. Useg=9.81 m/s² ,Solve Q5), Q6), and Q7).mRBQ5) The time of flight (ta-B) in (sec) is:а. 8.89b. 13.55c. 6.61d. 4.37е. 5.26

Given data VA = 21.8 m/s θA = 30 degrees g = 9.81 m/s2 To determine a) Time of flight (tA-B) b)…

It is observed that the skier leaves the ramp A at an angle OA = 30 degrees with the horizontal and a velocity VA =21.8 m/s. Use g=9.81 m/s² ,Solve Q5), Q6), and Q7). 4 m R Q5) The time of flight (tA-B) in (sec) is: а. 8.89 O b. 13.55 c. 6.61 O d. 4.37 е. 5.26

It is observed that the skier leaves the ramp A at an angle OA = 30 degrees with the horizontal and a velocity VA =21.8 m/s. Use g=9.81 m/s² ,Solve Q5), Q6), and Q7). 4 m R Q5) The time of flight (tA-B) in (sec) is: а. 8.89 O b. 13.55 c. 6.61 O d. 4.37 е. 5.26

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: uppose you are asked to conduct an experiment to study the impact of three factors(temperature: high…

A: Design of experiments (DOE) is nothing but a technique that is used to optimize the product cost and…

Q: Which of the following part designs would be preferred because it would result in lower production…

A: To be explained:- which method will give lower cost

Q: What is meant by the idea of testing individual units?

A: By the idea of testing individual units we mean that it is a process of software development in…

Q: A drawbridge is being raised by a cable El. The four joint loadings shown result from the weight of…

Q: A cube of edge 24mm is resting on the top of a frustum of cone of base diameter 60mm and top…

A: In case of Isometric projection:- The three edges of solid right angle of an object are shown by…

Q: Why can overtraining be a problem?

A: Overtraining can be a problem because- 1. Sometimes body does not cope up with the pressure of…

Q: Sheet Forming Processes; V-Bending of Sheets is more expensive than Edge Bending. (T or F) In Metal…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Q\Why the metals family could be strengthening

A: Both crystalline and amorphous materials may have their yield strength, ductility, and toughness…

Q: important property of many tool steals, is the ability of a tool steel to retain its mechanical and…

A: Yes, it is true.

Q: Sclect an appropriate manufacturing process where dimension accuracy and precisions are critical.…

A: Extreme tolerances are required to ensure proper performance and reliability. In automotive…

Q: What are assessments that measure strength, speed, agility, or high-speed strength? What are the…

A: The assessments that measure strength, speed, agility, or high-speed strength is T-Test

Q: An aluminium alloy component, is machined on a lathe. The lathe has a mechanical efficiency of 91%.…

A: ⇒given data;⇒mechanical efficiency(η)=91%⇒diameter(d)=150mm⇒lenth(l)=400mm⇒shear stength of aluminum…

Q: What is impact loading?

A: Impact loading is a type of loading whose period of action is very less. Generally, when the time of…

Q: what process is this? what are the factor that need to consider?

Q: what is FRP and write the properties and applications

A: Fiber-reinforced plastics (FRP): It is a type of composite material which is made of polymer with…

Q: Describe what a Nodal line is, then provide a real life example for it along with a diagram.

A: Nodal line is a line/curve which does not change (remains fixed) when the system undergoes…

Q: If the Quality Cost increases by 2.5% and the Production Index increases by 2.5%, then by how much…

A: Product index = ratio of quality costs to the total costs

Q: Describe the concept of finding toughness using impact testing machine.

Q: Q3/ Consider a point in a structural member that is subjected to plane stress. Normal and shear…

Q: What happens when Fabrication Errors occur?

A: Fabrication errors are defined as errors which are occurred due to improper or incorrect fabrication…

Q: (a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and…

A: Chemical machining and electrochemical machining

Q: When does damping occurs?

A: If a body is subjected to vibrations/oscillations and we need to reduce those, damping is done.…

Q: Select an appropriate manufacturing process, where dimensional accuracy and precision is not…

A: Introduction: There are different types of the manufacturing processes like casting, forming and…

Q: What is rectification

A: Rectification is the conversion of alternating current to direct current. Rectification is performed…

Q: Describe the operational characteristics of a Direct Acting Relief Valve B) A single paragraph…

A: The characteristics of a direct-acting relief valve can be used in a simple circuit to control the…

Q: Are car body styles exactly identical between years? Like does a 2009 Dodge Charger look identical…

A: The question is asking whether the body styles of cars remain exactly the same between different…

Q: What is line of impact?

A: The line of impact is the line along which the impact forces act during the collision. Generally, it…

Q: Q1- Compare between the ferrous and non-ferrous metals in terms of the strength, hardness, weight,…

A: Ferrous metals contain iron, and non-ferrous metals don't. That means each type of ferrous and…

Q: How is the Force Method of Analysis applied?

A: The force method of analysis is a method that is used to determine the unknown forces form the…

Q: For each of the mating part pairs below, and lower limit for each part. For A and B, səddn express…

Q: requirements form into different Shape, why do we need it in the design of machine elements well…

A: Machine elements are to be designed within elastic deformation regime because

Q: Give me the process of making a meat tenderizer using a shaper machine process. The picture below is…

A: As we know that it is a tool controlled by hand which makes mellow pieces of meat for cooking.

Q: Estimate the manufacturing cost for a simple machined component: a. Compare the costs for…

A: To Compare:a) The costs for manufacturing volumes of and pieces with an intermediate tolerance and…

Q: In the hardness test, answer the questions 1- What happens to the sample if its thickness is less…

A: Thickness of the specimen should be at least seven times of the depth of the indentation. It allows…

Q: b) Use your own sketches to show how surface finish is measured and define 2 important parameters…

A: B) Surface finish is a characteristic of any machined surface. It is sometimes called surface…

Q: 28 - Which one is not one of the usage areas of control gauges? A) Control gauges are used to…

A: Option D : Control gauge are used to measure axial misalignment.

Q: For the mass production of flat metal sheet shapes; Waterjet cutting is the most appropriate…

A: given : Work piece : sheet metal - mass production proposed machining options Water jet cutting…

Q: What are damped vibrations?

A: Damped vibrations are the vibrations in which the system's vibrational energy is dissipated…

Q: Which order arranges the following manufacturing processes from the least precise to the most…

A: The casting is a type of manufacturing process in which the liquid material is poured into a hollow…

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

100%

Dynamic

Q6) The distance R in (m) is:
a. 77.08
O b. 156.03
O c. 103.18
O d. 88.24
O e. 124.22
Q7) The vertical component of the velocity
(downward) of skier at B in (m/s) is:
a. 42.09
O b. 30.79
c. 40.74
O d. 77.15
O e. 53.59

It is observed that the skier leaves the ramp
A at an angle 0A = 30 degrees with the
horizontal and a velocity VA =21.8 m/s. Use
g=9.81 m/s² ,Solve Q5), Q6), and Q7).
m
R
B
Q5) The time of flight (ta-B) in (sec) is:
а. 8.89
b. 13.55
c. 6.61
d. 4.37
е. 5.26

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Today, the two most important processes in steelmaking are which of the following (two correct answers): Group of answer choices basic oxygen furnace Bessemer converter electric arc furnace induction furnace open hearth furnace answers a and c
Please don't provide handwritten solution .....
Please guide me through the procedure of thoroughly testing individual components.
provide complete answer
Why 100% of the total material is not possible for 100% sampling
Manufacturing Processes Q1. Chose the correct answer: 1. Which of the following are variations of sheet-metal-bending operations: (a) coining, (b) flanging, (c) hemming, (d) ironing, (e) notching, (f) shear spinning, (g) trimming, and (h) tube bending? 2. Springback in a sheet-metal-bending operation is the result of which one of the following: (a) elastic modulus of the metal, (b) elastic recovery of the metal, (c) overbending, (d) overstraining, or (e) yield strength of the metal? 3. The cutting force in a sheet-metal blanking operation depends on which mechanical property of the metal (one correct answer): (a) compressive strength, (b) modulus of elasticity, (c) shear strength, (d) strain rate, (e) tensile strength, or (f) yield strength? 4. A circular sheet-metal slug produced in a hole punching operation will have the same diameter as (a) the die opening or (b) the punch? 5. As sheet-metal stock hardness increases in a blanking operation, the clearance between punch and die should…
26c)A material has an mean indentation diameter of 3.64 mm created by a 5 mm diameter Brinell Indenter. Its hardness value is 200 HB , what will be applied force in Newtons?
In order to produce parts form materials that are hard and brittle Casting and sintering are often utilised Extrusion and forming processes dominate Additive manufacturing is utilised Machining to shape is always favoured
Sub: Advanced Manufacturing Process
what type of grinding wheel should be used to get the required finish on this part using a surface grinder?
what is the range of gear sizes can be achieved by forging, extrusion and metal removal processes.
You have the following information: (IMAGE) Taking into account the above, answer the following questions: 1) Calculate the safety stock that allows for 5 stockouts in a year. 2) Calculate the reorder point that will allow for these 5 stockouts in a year. 3) Calculate the number of stockouts in a year, corresponding to a safety factor of 0.84. 4) Calculate the reorder point that allows the number of stockouts corresponding to a safety factor of 0.84.