It is required to water pump through a pipe(P.V.C) of diameter = 2 inches and 100 m, head to a storage tank of 20 m height, the pipe contains five gate valves, two swing check and ten standard elbows. Find the flowrate, head of operation and motor power in the following case: Two pumps are conected at series. The characteristics of pump are given below: Q m³/hr 50 100 150 200 H m 425 350 250 162.5 25

It is required to water pump through a pipe(P.V.C) of diameter = 2 inches and 100 m, head to a storage tank of 20 m height, the pipe contains five gate valves, two swing check and ten standard elbows. Find the flowrate, head of operation and motor power in the following case: Two pumps are conected at series. The characteristics of pump are given below: Q m³/hr 50 100 150 200 H m 425 350 250 162.5 25

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
A 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point of discharge 24.4 m higher than the pump. There are four 90° elbow in the line. Find the pumps dynamic discharge head. Use Table of Equivalent Length of Straight Pipe (see image). Please help. Thank you :)
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
A Kaplan turbine runner is to designed to develop 10000 hp, the net head is 5.5 m. Assume that the speed ratio is 2.09 and the flow ratio is 0.68, and the overall efficiency is 60%. The diameter of the boss is 1/3 rd of the diameter of the runner . The discharge is ؟
B Refer to, Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be frictionless in the siphon. Find the rate of discharge in mºls and the pressure head at B if the pipe has a uniform diameter of 150 mm. M Tar N
Air @ 68°C is pumped through a pipe of internal d = 6.4in: If the vol flowrate is set to 6.2 ft3/min, is the flow laminar or turbulent? assume P is atmospheric.
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
A sharp edged orifice will be required to produce a discharge of 35 liters/sec of water under a head of 3m. Find the required diameter, when C = 0.595
In a certain hydraulic turbomachine, the following data apply:Inlet blade velocity is 20 m/s. Vu1=21 m/s; Vr1=10 m/s.At the exit, V2 is purely axial and has a value of 14 m/s, and blade speed is9 m/s. Is this power absorbing or power producing? Find E and the changes instatic and stagnation pressures. Would this machine be classified as a purelyradial, purely axial, or mixed flow type?Ans: E=420 J/kg; Δpstag=420 kPa; Δpstat=247.4 kPa
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4.5 times the velocity head in the siphon. Determine the flow rate in the siphon in lit/sec Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: li/s Decimal Places required in the final answer: 3