A JE Ris the total resistance of two resistors, connected in parallel, with resistances R1 and6.R2, then11.1R.R1R2(a) Find ôR/ƏR1 and ôR/8R2.(b) If the resistances are measured in ohms as Rin each case, estimate the percentage error in the calculated value of R.25N and R2402, with a possible error of 0.5%

Find R interms of R1 and R2 Integrate with respect to R1 and R2 keeping other constant Apply…

JE Ris the total resistance of two resistors, connected in parallel, with resistances R and 6. R2, then 1 1 1 R. R1 R2 (a) Find OR/aR1 and OR/8R2. (b) If the resistances are measured in ohms as R, in each case, estimate the percentage error in the calculated value of R. = 252 and R2 = 402, with a possible error of 0.5%

JE Ris the total resistance of two resistors, connected in parallel, with resistances R and 6. R2, then 1 1 1 R. R1 R2 (a) Find OR/aR1 and OR/8R2. (b) If the resistances are measured in ohms as R, in each case, estimate the percentage error in the calculated value of R. = 252 and R2 = 402, with a possible error of 0.5%

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2P: The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where...

See similar textbooks

Similar questions

The temperature dependence of resistance is also quantified by the relation R2=R1[ 1+(T2T1) ] where R1 and R2 are the resistances at temperatures T1 and T2, respectively, and is known as the temperature coefficient of resistance. If a copper wire has a resistance of 55 at 20C, find the maximum permissible operating temperature of the wire if its resistance is to increase by at most 20. Take the temperature coefficient at 20C to be =0.00382.
Explain the difference between cumulative- and differential-compounded connections.
Using the diagram, solve for the Rth, Vth, and load current (IL) through each resistance using Thevenin’s Theorem. Please draw the circuit diagram for each Rth and Vth computation.
a) Compare metallic foil vs semiconductor strain gauges (construction, advantages and disadvantages). b) Consider a Wheatstone bridge circuit (Figure 1) that has all resistances equal to 250 ?. The resistance R1 is a strain gauge that cannot sustain a power dissipation of more than 0.25 W. What is the maximum applied voltage that can be used for this bridge circuit? At this level of bridge excitation, what is the bridge sensitivity?
If R0= 44 milliohms and Ri= 736 ohms, what is R1 , R2, R3 in the equivalent circuit????
For the given circuit find the VRL Voltage of the load; VR Voltage in the resistance R; Iz Current of the Zener diode and the Pz Power in the Zener diode. VRL = ? Iz = ? Pz = ? If the Zener diode in the figure has an elbow tension of 0.7 V. Zener breaking voltage of VZ = - 15 V Vin = 40 V R = 1 kohm RL= 3 kohm Requirement: Take out Vth by mesh method and solve equations
As the gauge shown is compressed/expanded the resistance of the strain gauge changes commensurately with thedirection and magnitude of load. Develop an understanding as to why the resistance changes i.e. increases ordecreases from its nominal value. Then, Assume a 5volt DC supply, and 350 Ohms as the balanced nominal resistance to our circuit where thedifferential voltage across A and B is zero. Assume that the Resistance-force sensitivity is 25Ohm/10Newtons. Find the voltage across A and B for +10N,-30N, +100N, -0.1N.
A load resistor RL is in parallel with a noisy source (vS << VS), and a biasing component, which canbe a linear or a nonlinear element. Suppose we can write the total source voltage vS and the totalload voltage vL as shown in the image. Answer the ff and explain clearly. i. Let the biasing component be a linear resistor with resistance RB. Without the noise, determinethe value of RB so that the load voltage is 5V. ii. With the noise, determine the ratio of the load voltage noise and the source noise (vI /vS )..
Write the application of extra super tension that have rating 132KV and what used for?
Commercially available strain gages, typically, have nominal resistance of either 120 or 350 Ohm. Discuss the advantages and disadvantages of each type in terms of measurement accuracy/precision and sensitivity.
For the JFET shown in Figure, Determine the minimum value of VDD required to put the device in the constant-current region of operation when VGS = 0 V. where VGS(off) = - 4 and IDSS = 42mA
. a) Calculate and plot the current flowing through the pn junctions of device #2 on your 3311 wafer as a function of voltage over the range of -3 volts to plus 1.5 (or so) volts on a linear scale. b) plot the I-V curve for the forward voltage on a log scale. c) What voltages correspond to 10 A/cm2, 100 A/cm2, 1000 A/cm2, 10,000 A/cm2 and 100,000 A/cm2? d) What is the current and current density when the applied voltage is equal to the built-in voltage? e) what are your thoughts on applying a voltage greater than the built-in voltage to a pn junction diode?