) A large pipe with a cross-sectional area of 1 m' descends 5 m and narrows to 0.5 m2, where it terminates in a valve at point O (Fig. 9). If the pressure at point ® is atmospheric pressure, and the valve is opened wide and water allowed to flow freely, find the speed of the water leaving the pipe. (2) Po v, h Po Fig. 9

) A large pipe with a cross-sectional area of 1 m' descends 5 m and narrows to 0.5 m2, where it terminates in a valve at point O (Fig. 9). If the pressure at point ® is atmospheric pressure, and the valve is opened wide and water allowed to flow freely, find the speed of the water leaving the pipe. (2) Po v, h Po Fig. 9

Name: ) A large pipe with a cross-sectional area of 1 m' descends 5 m and n
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: ) A large pipe with a cross-sectional area of 1 m' descends 5 m and narrows to 0.5 m2, where it terminates in avalve at point O (Fig. 9). If the pressure at point ® is atmospheric pressure, and the valve is opened wide andwater allowed to flow freel

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The waterwheel in Fig. is being driven at 200 r/minby a 150-ft/s jet of water at 20 ° C. The jet diameter is 2.5 in.Assuming no losses, what is the horsepower developed bythe wheel? For what speed Ω r/min will the horsepowerdeveloped be a maximum? Assume that there are manybuckets on the waterwheel.
Consider the water siphon shown, if the tube is 1 cm in diameterand z1 = 60 cm, z2 = -25 cm, z3 = 90 cm and z4 = 35 cm, estimatethe flowrate in cm3/s.
A test on 30-cm-diameter pipe with water showed a gage difference of 33 cm on mercury-water manometer connected to two piezometer rings 120 m apart. The flow was 0.23 m/s. What is the friction factor?
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A jet of water issues from a kitchen faucet and falls vertically downward at a flow rate of 34 mL/s. At the faucet,which is 35 cm above the sink bottom, the jet diameter is 1.5 cm. Determine the diameter of the jet where it strikes the sink.
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Water at 20°C flows through the orifice in Fig. ,which is monitored by a mercury manometer. If d = 3 cm,(a) what is h when the flow rate is 20 m3/h and (b) what isQ in m3/h when h = 58 cm?
pls replyy Gasoline (SG-0.7) flows down an inclined pipe whose upper and lower sections are 90 mm (section 1) and 60 mm (section 2) in diameter respectively. The pressure and velocity in section 1 are 280 kPa and 2.3 m/s respectively. If the difference in elevation between the 2 sections is 2.5m, find the pressure at point 2.
O.S. A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cv=0.95, Cv = 0.62 as shown in the figure. If the liquid is oil (s.g. = 0.85), what is the head, h in meter over the orifice is required? determine the theoretical velocity of the jet determine the theoretical flow (Ips).
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Find the pressure head at entry of the pipe, when the pressure of flowing fluid is 275 N/cm? The pressure head at entry (Unit in Pascal)?