Las=60cm 45° B Platform C v-10cm/s Disk B (radius=30cm) rolls without sliding relative to Platform C as the platform is moving upwards with a velocity 10cm/s. At the instant shown, determine the following: Identify the rigid bodies in the system and the type of motion of each body. Determine the magnitude of velocity of the disk's center, Vs Determine the angular velocity of Disk B, we Determine the angular velocity of member AB, WAB a. b. С. d.

Las=60cm 45° B Platform C v-10cm/s Disk B (radius=30cm) rolls without sliding relative to Platform C as the platform is moving upwards with a velocity 10cm/s. At the instant shown, determine the following: Identify the rigid bodies in the system and the type of motion of each body. Determine the magnitude of velocity of the disk's center, Vs Determine the angular velocity of Disk B, we Determine the angular velocity of member AB, WAB a. b. С. d.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the figure shown, the hydraulic cylinder moves upwards with a constant speed of Va=0.2 m/s, transferring vertical movement to corner A of the container. If bearing b never slips and has a diameter of 8 cm, determine the angular velocity of the imaginary line drawn from its axis of rotation to any point on its periphery. Determine the angular velocity of side CD at this moment.
(Three-Dimensional Motion) The figure below represents a pair of bevel gears A and B. Gear A rotates in ahorizontal plane about a vertical axis at O. Gear B rotates around the shaft OC which in turn rotates about the terminal axis at O. determine the angular accelera tion of gear B when gear A is stationary and member OC has an angular velocity of 10j rad/sec and and angular acceleration of 25j rad/sec2 .
Disk B is at rest when it is brought into contact with disk A, which is rotating freely at 450 rpm clockwise. After 6 seconds of slippage, during which each disk has a constant angular acceleration, disk A reaches a final angular velocity of 140 rpm clockwise Disk radius a =3 in Disk radius b= 5 in. Determine the final linear speed at the point of contact between the disk in in/s
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
Lever is attached to a gear of radius R_1 = 0.50 in and moment of inertia I_1 = 1.0 kg m^2. This gear meshes with a second gear of radius R_2 = 1.0 m and moment of inertia I_2 = 16.0 kgm^2. Each gear rotates about a fixed axis running through its center. Force F = 2.0 N is applied on the lever at a distance of 1.0 m from the center of the gear. What is the angular acceleration of each gear?
The connecting rod of a horizontal reciprocating engine is 400 mm and length of the stroke is 200mm. The mass of the reciprocating parts is 125 kg and that the connecting rod is 100 kg. The radius of gyration of the connecting rod about an axis through the centre of gravity is 120 mm and the distance of centre of gravity of the connecting rod from big end centre is 160 mm. The engine runs at750 r.p.m. Determine graphically the torque exerted on the crankshaft when the crank has turned 30° from the inner dead centre.
A cyclist pedals constantly at 7.9587 rad/s the wheels are 336.5mm in radius. If the chain is directly connected with the sprockets which are 76 mm in radius (front sprocket) and 35mm in radius (rear sprockets), Determine the angular speed of the wheel in rad/s.
An engine flywheel has a mass of 120 kg and a radius of gyration of 630 mm. At an instant when the flywheel runs at 600 rev/min, an acceleration torque of 150 Nm was applied for a period of 10 seconds. Determine the: (i) final speed of the flywheel in rev/min. (ii) number of flywheel revolutions made during the acceleration period. (iii) kinetic energy of rotation of the flywheel.
The turbine rotor of a ship has a mass of 2.2 tonnes and CO1(L2) rotates at 1800 rpm clockwise when viewed from the aft The radius of gyration of the rotor is 320 mm. Determine the gyroscopic couple and its effect when (a) The ship turns right at a radius of 250 m with a speed of 25 km/h. (b) The ship pitches with the bow rising at an angular velocity of 0.8 rad/s (c) The ship rolls at an angular velocity of 0.1 rad/s.
Draw the impulse-momentum diagram and line of action for e. Solve for the following: 1. Determine the angular velocity of the slender bar (B) immediately after impact. angular velocity of A = 57.1 rad/s since there is no external torque 2. Determine the linear velocities of both the sphere (A) and the slender bar (B) immediately after impact at their centroids ANSWERS I GOT BUT ARE INCORRECT: (the unit is given) angular velocity of the slender bar (B) immediately after impact: 8.089 rad/s , 18.49 rad/s linear velocity of the sphere (A) immediately after impact at the centroid: 0.485 rad/s^2, 0.16 rad/s^2, 2.11 rad/s^2 linear velocity of the slender bar (B) immediately after impact at the centroid: 0.485 rad/s^2, 0.49 rad/s^2, 2.21 rad/s^2
Ring C moves downwards at 2 m/s. Determine the value of point B velocity (vB =?), Angular velocity of the arm CB (wBC) and the position vector B in relation to C rB/C for the situation shown in the figure.
The mass of a rocket is m, and its radius of gyration about the mass center C is kC. Determine the thrust T that can cause an angular acceleration of alpha when applied at θ. Calculate the components of the absolute acceleration of point A, ax, ay , caused by this thrust. Point C is the center of mass of the rocket. At the moment considered the angular velocity of the rocket is zero. The gravitational acceleration: g = 9.81 m/s m= 6800kg kc= 3m alpha = 0.24 m/s^2 l1= 6.4 m l2= 6m theta = 5 degree radius of gyration is given with respect to C