Answered: final speed of the flywheel in rev/min.…

final speed of the flywheel in rev/min. (ii) number of flywheel revolutions made during the acceleration period. (iii) kinetic energy of rotation of the flywheel.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel and shaft together have a mass of 800 kg. The combined mass has a radius of gyration of 400 mm. An accelerating torque of 10 N m is applied to the stationary flywheel for 100 s. There is a constant resisting torque due to friction of 2 N m. Determine (a) the angular acceleration, (b) the angular velocity of the flywheel after 100 s (in RPM)
The blade of an oscillating fan and the rotor of its motor shown have a total weight of 1 kg and a combined radius of gyration (for all axes) of 100 mm. They are supported by bearings at A and B, 125 mm apart, and rotate at the rate ω1 = 2000 rpm. Determine; a) the dynamic reactions at A and B when the motor casing has an angular velocity ω2 = (0.5 j+1.5 k) rad/s. b) the static reactions at A and B when the fan has stopped. Note: Assume that the center of mass of the entire system is between the middle of the bearings of A and B, that is 62.5 mm away from bearing A.
The bar AB of 3.62kg is attached to the collar A of negligible mass and a wheel of mass 15.81kg with a turning radius of 0.16m. If at the position shown the angular velocity of the wheel is 67rpm clockwise, determine the velocity of the wheel in RPM when point B is located just below C. The angle of the bar with respect to Y is 19.47°. The answer is 93.89
A 5.32-kg disk A of radius 0.445 m initially rotating counter-clockwise at 436 rev/min is engaged with a 6.72-kg disk B of radius 0.275 m initially rotating clockwise at 528 rev/min, where the moment of inertia of a disk is given as I = ½ mi?. Determine their combined angular speed (in rpm) and direction of rotation after the meshing of the two disks. Remember to show clearly the equations that you use!!'
The turbine rotor of a ship has a mass of 2.2 tonnes and CO1(L2) rotates at 1800 rpm clockwise when viewed from the aft The radius of gyration of the rotor is 320 mm. Determine the gyroscopic couple and its effect when (a) The ship turns right at a radius of 250 m with a speed of 25 km/h. (b) The ship pitches with the bow rising at an angular velocity of 0.8 rad/s (c) The ship rolls at an angular velocity of 0.1 rad/s.
A gear engine automobile is traveling along a curved track of 120m radius. Each of the four wheels has a moment of inertia of 2.3 kg m2 and an effective diameter of 600 mm. The rotating parts of the engine have a moment of inertia of1.25kg m2 the gear ratio of the engine to back wheel is 3:2.The engine axis is parallel to the gear axle and the crank shaft rotates in the same sense as the road wheels. The mass of the vehicle is 2050 kg and the center of mass is 520 mm above the road level. The width by the track is 1.6m, what will be the limiting speed of the vehicle if all the four wheels maintain contact with the road surface (b) Explain the function of a flywheel from a crank effort diagram.
A rope drum of diameter 850 mm and mass 1000 kg is used in a machine lifting procedure. The drum reaches a top rotational speed of 475 rev/min from rest in a time of 25 s. Determine: (i) the maximum linear speed of the rope;(ii) the angular acceleration of the rope drum;(iii) the moment of inertia of the rope drum, given that its radius of gyration is 250 mm;(iv) the accelerating torque applied to the rope drum.
A flywheel weighing 4480 lbs has a radius of gyration of 3 ft. If there is a driving torque of 600 lb-ft, and a resisting torque of 250 lb-ft, find the time required to increase its speed from 20 to 80 rpm. The correct answer is 22.5 seconds.
Inside a machine, two gears, A and B, HINGED at their centers, are meshed with each other such that gear A transmits torque and speed to gear B. Gear A has a mass mA=2 kg, radius rA=175 mm, and radius of gyration kA=150 mm. Gear B has a mass B=5 kg, radius rB=525 mm, and radius of gyration kB=400 mm. From rest, a counter-clockwise couple M of constant magnitude 6 Nm is applied to Gear A. Which of the following is closest to the magnitude of the angular acceleration of gear B, in radians per square seconds (rad/s2)?3.0044.814.9445.6
Determine the constant torque that must be applied to a 50-kg flywheel, with radius of gyration45 cm, to give it a frequency of 300 rpm in 10 secs if its initially at rest. Please help me solve this problem with clear and complete solution. Please also include an illustration from the given.
In the helicopter shown; a vertical tail propeller is used to pre- vent rotation of the cab as the speed of the main blades is changed. Assuming that the tail propeller is not operating determine the final angular velocity of the cab after the speed of the main blades has been changed from I80 to 240 rpm. (The speed of the main blades is measured relative to the cab, and the cab has a centroidal moment of inertia of 650 lb.ft.s2. Each of the four main blades is assumed to be a slender rod 14 ft weighing 55 lb.)
A four wheeled trolley car has a total mass 3000kg. Each axle with its two wheels and gears has a total moment of inertia of 32kgm2. Each wheel is of 400mm radius. The centre distance between the two wheels on an axle is 1.4m. Each axle is driven by a motor with a speed ratio of 1.3. Each along with it gear has a moment of inertia of 16kgm2 and rotates in the opposite direction to that of the axle. The centre of mass of the car is 1m above the rails. Calculate the limiting speed of the car when it has to travel around a curve of 250m radius without the wheels leaving the road.