Item 2Learning Goal:A piston is driven by a crankshaft as shown. The crankarm (member AB) has a length of ri = 0.40 in andthe connecting rod (member BC) has a length ofr2 = 4.65 in. The crankshaft rotates in thecounterclockwise or positive direction. (Figure 1)Figure38°FSunnyQC12W₂@1ØB<1 of 1PaFind(meExp▶ VVCSubPart D ComProvide Feed! Part C - Velocity of CVC=SubmitFind the magnitude of the velocity of C, vc, when the piston has moved to the new position = 36.0° and = 3.99°. The crankshaft(member AB) is still rotating at 290 rpm.Express your answer to three significant figures and include the appropriate units.► View Available Hint(s)īProvide FeedbackμAValuePart D Complete previous part(s)UnitsH?<O2 of 7ReviewNext >4:05 PM11/22/2022

To find: The magnitude of velocity of C. Given: The crank arm length, r1 =0.40 inch. The connecting…

Learning Goal: A piston is driven by a crankshaft as shown. The crank arm (member AB) has a length of ri = 0.40 in and the connecting rod (member BC) has a length of r2 = 4.65 in. The crankshaft rotates in the counterclockwise or positive direction.(Figure 1)

Learning Goal: A piston is driven by a crankshaft as shown. The crank arm (member AB) has a length of ri = 0.40 in and the connecting rod (member BC) has a length of r2 = 4.65 in. The crankshaft rotates in the counterclockwise or positive direction.(Figure 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rigid block is supported by two cables having the same diameter of 4 mm. Cable S1 is made of AISI 1050 cold drawn steel with E=200,000 MPa, Sy=580 MPa, and Sult=690 MPa; cable S2 is made of AISI 1020 cold drawn steel with E=200,000 MPa, Sy=390 MPa, and Sult=470 MPa. Determine the maximum number of cycles n3 due to the following history of P.
QUESTION 7 Figure 7 shows an assembly consist of circular shaft AB, solid circular BC and a circular CE. The shaft is made of titanium alloy steel and fixed at A. Segment AB is a hollow shaft, has an inner diameter of 25mm. While tube CE with the thickness 2mm has an outer diameter of 20mm. The assembly is subjected to torques of 1000 Nm at C, 210 m at D and 350 Nm at E. The alloy has modulus of rigidity, G = 44kN/mm^2 a) Draw the torque diagram of the shaft. b) Determine maximum shearing stress developed in each segment. c) Calculate the angle of twist at the right end of the shaft.
A motor (located at C) provides 50kW of power which is then used by pulleys A and B. When the motor is running, the transmission shaft (which is made of Cr-Ni steel and has a diameter of 5cm) starts rotating at a speed of 200 rpm. 1) Find the moment of force at pulleys A, B and C. 2) Find the torque in each section (between the pulleys). 3) What is the safety factor of the driveshaft on the ultimate limit?
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2 , σc = 200 N/mm2 ; For pin material, τ = 35 N/mm2 , σt = 133 N/mm2 ; For flange material τ = 16.67 N/mm2 . The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling. Explain Axle, Spindle, Counter shaft and line-shaft with their examples .
A bushed pin type flexible coupling is used to transmit 10 kW power at 720 rpm. The design torque is 150% of rated torque. The keys have square cross-section. The permissible stresses are: For shaft and key material, τ = 66.67 N/mm2, σc = 200 N/mm2; For pin material, τ = 35 N/mm2, σt = 133 N/mm2; For flange material τ = 16.67 N/mm2. The permissible bearing pressure for rubber bushes is 1 N/mm2. The number of bushes is 4. Design the bushed pin flexible coupling.
.A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300mm in diameter, and four 19 – mm aluminum bolts on a concentric bolt circle 200 mm in diameter.What torque can be applied without exceeding 62 MPa in the steel or 42 MPa in the aluminum?Assume Gst = 82.7 GPa and Gal = 27.6 GPa.
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm objects falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie: 1. The minimum wire diameter is most nearly A. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in 2. The mean coil diameter is most nearly A. 8.6 in B. 10 in C. 13 in D. 16 in 3. The number of active coils is most nearly A. 8 B. 11 C. 12 D. 14
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
3) A flange coupling is to connect two 60mm shafts. The hubs of the coupling are 120mm, 100mm thick, & the flange webs are 20 mm thick. Six M16 bolts fasten the flange from a 165 bolt circle. The keyway is 15mm shorter than the hub’s thickness & the key is 15mm x 15mm. The coupling transmits 45kW @ 450rpm. The yield point in shear for all materials is half of its yield point in tension or compression. Yield tensile strength is 0.75 of ultimate strength of the materials. The Sult is 448N/mm2 . Find: (a) the shear stress in key; (b) the bearing stress in key; (c) the shear stress in bolts; (d) bearing stress in flange.