Learning Goal: To analyze and design a passive, first-order high-pass filter using a series RC circuit. An instrument needs to detect periodic signals of approximately 5000 Hz. The instrument operates in an environment with a lot of periodic noise ranging from a few to several hundred hertz. A high-pass RC filter can be built using available 4.0 μF capacitors; resistors of any necessary value are also available. Express your answer to three significant figures and include appropriate units. R = Submit Value Ω Part C - Measuring the effectiveness of the series RC high-pass filter To measure the effectiveness of the design, find the magnitude of the output voltage of the series RC high-pass filter for the given frequencies. Use an input voltage of 1 V. Express your answers, separated by commas, to three significant figures in units of volts. Vout (60 Hz)|, |Vout (2800 Hz)|, |Vout (5000 Hz)| = = V, V, V

Learning Goal: To analyze and design a passive, first-order high-pass filter using a series RC circuit. An instrument needs to detect periodic signals of approximately 5000 Hz. The instrument operates in an environment with a lot of periodic noise ranging from a few to several hundred hertz. A high-pass RC filter can be built using available 4.0 μF capacitors; resistors of any necessary value are also available. Express your answer to three significant figures and include appropriate units. R = Submit Value Ω Part C - Measuring the effectiveness of the series RC high-pass filter To measure the effectiveness of the design, find the magnitude of the output voltage of the series RC high-pass filter for the given frequencies. Use an input voltage of 1 V. Express your answers, separated by commas, to three significant figures in units of volts. Vout (60 Hz)|, |Vout (2800 Hz)|, |Vout (5000 Hz)| = = V, V, V

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The low-pass filter designed has an input of 2cosωt V. 1. Suppose the power supplies are ±Vcc. What is the smallest value ofVcc that will still cause the op amp to operate in its linear region? 2. Find the output voltage when ω=ωc.3. Find the output voltage when ω=0.1ωc.4. Find the output voltage when ω=10ωc.
Measurements conducted on a servomechanism show the system response to be: C (t) = 0.3 e 60t + 1.5 e 10t, when subjected to a unit step input. [1].Obtain the expression for the closed-loop transfer function. [2].Determine the undamped natural frequency and damping ratio of the system.
Know the op amp circuits that behave as first-order lowpass and high-pass filters and be able to calculate their component values Compute the values for R2 and C that yield a high-pass filter with a passband gain of 1 and a cutoff frequency of 1 rad / s if R1 is 1Ω. (Note: This is the prototype high-pass filter.)
a) Determine the algebraic representation of the transfer function of the LTI system above. It is known that one of the poles of the transfer function of the above system is s= -4. b) Draw the region of convergence (ROC) of the transfer function in the plane along with the location of the zero-poles (if any). c) Determine the impulse response of the above LTI system! d) Is the above LTI system a Causal System? Explain your answer!
A band pass filter (BP) is required, with cutoff frequencies 500 Hz and 1kHz, to process the stream of an audio signal sampled at 8ksps. Design 1. Use DSP functions from Matlab for the design and practical realization of the BP filter in its FIR version with 64 taps. Specify the values for the cutoff frequency fp and stopping frequency fs of the BP filter, in terms of the Nyquist frequency. please share me the code in .m
a) Determine the algebraic representation of the transfer function of the LTI system above. It is known that one of the poles of the transfer function of the above system is s= -4. b) Draw the region of convergence (ROC) of the transfer function in the plane along with the location of the zero-poles (if any). c) Determine the impulse response of the above LTI system!
High-frequency ECG biopotentials analysis in the ST-T segment of a high-resolution ECG signal recording requires the analysis of signal components above 30 Hz and below 800 Hz. Design a first order band pass passive filter to accommodate this specified frequency bandwidth. Sketch the circuit configuration. You may use an opamp buffer stage in your circuit design.
Find the impulse response of matched filter matched to the signal V(t) which is 1200 split phasesignal Then find the maximum obtainable SNR at its output with V 1 µV η 10 17 W/Hz
The signal s(n)s(n) is recorded with frequency sampling Fs=500HzFs=500Hz. What's the duration of the following part s1(n)s1(n) of the signal s(n)s(n) where s1=s(601:4:5000)
PARTS A- C Read and Solve carefully please Write clearly and Box the Final answer(s) & label them Part A - What is the characteristic equation for the following transfer function? Part B - Determine the poles of the transfer function. Part C - Is the system BIBO stable or unstable?
The CT signal x(t)=3cos (600πt) + 6cos2(mπt) is critically sampled (Nyquist rate)by fs=4000 Hz. Find:i. The value of m.ii. The frequency components of the signal.iii. The frequency resolution (∆f) of the output spectrum if the sampled signal isprocessed by 64 point-DFT.iv. Define frequency resolution.
Given the circuit below, the transfer function Vo/Vi = (1) ______, when the output is the voltage across the capacitor. Using the transfer function, (2) What is the output voltage at t = 0? (3) What is the current through R2 at t = 0? (3) What is the output voltage at time infinity?(4) What is the current through R2 at time infinity?