Let's consider an axially loaded member having solid circular cross-section and subjected to th shown loads. Determine the displacement of end C with respect to A. Note that section AB has a diameter of 30 mm and section BC has a diameter of 20 mm. both section are made of steel having a modulus of elasticity E of 200 GPa. 15 kN A 1 m B 5 KN 0.7 m C 10 kN

Let's consider an axially loaded member having solid circular cross-section and subjected to th shown loads. Determine the displacement of end C with respect to A. Note that section AB has a diameter of 30 mm and section BC has a diameter of 20 mm. both section are made of steel having a modulus of elasticity E of 200 GPa. 15 kN A 1 m B 5 KN 0.7 m C 10 kN

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.13P: A steel pipe column with pinned ends supports an axial load P = 21 kips. The pipe has outside and...

See similar textbooks

Similar questions

A W8 × 28 steel wide-flange column with pinned ends carries an axial load P. What is the maximum permissible length of the column if (a) P = 50 kips, and (b) P = 100 kips? (Assume E = 29,000 ksi and y = 36 ksi.)
A 75 mm diameter compound bar is constructed by shrinking a circularbrass bush onto the outside of a 45 mm diameter solid steel rod. If thecompound bar is then subjected to an axial compressive load of 170 kN,determine the load carried by the steel rod. The modulus of elasticity for steel,Es = 200 GN/m2 , and brass, Eb = 100 GN/m2
The strut is supported by a pin at C and an A-36 steel (Young’s Modulus is 200 GPa) guy wire AB. If the wire has a diameter of 5 mm, determine how much it stretches when the distributed load acts on the strut. W0=11Kn/m
Two vertical steel wires each 1.5mm diameter and 1.2m long support a light rod over a span of 0.3m. A concentrated load of 250N is then applied vertically downwards at a point 0.1m from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E=200 GPa (Complete Solution)
Determine the changes in length, breadth and thickness of a steel bar which is 4 m long, 30 mm wide and 20 mm thick and is subjected to an axial pull of 30 kN in the directions of its length. Take Young’s Modulus as 70 GPa and Poisson’s ratio as 0.3.
A hollow circular column of 200 mm external and 160 mm internal diameter is subject to anaxial compressive load of 150 kN with an eccentricity of 25 mm from the centroidal axis.The column is 5.0 m long and both ends fixed. Determine the maximum compressive stressand deflection in the column (assume E = 120 GPa).
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
A closely coiled helical spring is made of 6 mm wire. The maximum shear stress and deflection under a 200 N load is not to exceed 80 MPa and 11 mm respectively. Determine the no. of coils and their mean diameter. Take C = 84MPa .
The assembly below consists of a steel rod CB and an aluminium rod BA, each having a diameter of 12 mm. If the rod is subjected to the axial loadings at A and at the coupling B, determine the displacement of the coupling B and the end A. The unstretched length of each segment is shown below. Neglect the size of the connections at B and C, and assume that they are rigid. Est = 200 GPa, Eal = 70 GPa.
Determine the diameter of a circular rod made of ductile material with a fatigue strength (complete stress reversal) σe = 280 MPa and a tensile yield strength of 350 MPa. The member is subjected to a varying axial load from 700 kN to – 300 kN. Assume Kt = 1.8 and F.S. = 2.
a) Determine the downward displacement δ of the lower end of the copper bar with respect to the base support of the steel post at point A due to a load P = 150 kN. b)What is the maximum permissible load Pmax if the displacement δ is limited to 1.0 mm?
The shaft assembly is made from a steel tube 1 in. in diameter, which is bonded to a solid brass core 0.5 in. in diameter. If a torque of 250 lb-ft is applied at its end, determine the maximum shear stress in psi experienced by the assembly. Take G for steel at 11.4x103 ksi and G brass at 5.2 x 103 ksi. complete soln.