A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 45 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 170 kN, determine the load carried by the steel rod. The modulus of elasticity for steel, Es = 200 GN/m2 , and brass, Eb = 100 GN/m2

A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 45 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 170 kN, determine the load carried by the steel rod. The modulus of elasticity for steel, Es = 200 GN/m2 , and brass, Eb = 100 GN/m2

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.24P

See similar textbooks

Similar questions

A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
An aluminum tube AB with a circular cross section has a sliding support at the base and is pinned at the top to a horizontal beam supporting a load Q = 200 kN (sec figure). Determine the required thickness t of the tube if its outside diameter d is 200 mm and the desired factor of safety with respect to Eu 1er buckling is n = 3.0. (Assume E = 72 GPa.)
A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 6 ft, 9 ft, 12 ft, and 15 ft. The column has an outside diameter d = 6.625 in. and wall thickness t = 0.280 in, (Assume E = 29,000 ksi and y= 36 ksi.)
A sign for an automobile service station is supported by two aluminum poles of hollow circular cross section, as shown in the figure. The poles are being designed to resist a wind pressure of 75 lb/ft" against the full area of the sign. The dimensions of the poles and sign are hx= 20 ft, /r =5 ft, and h = 10 ft. To prevent buckling of the walls of the poles, the thickness e is specified as one-tenth the outside diameter d. (a) Determine the minimum required diameter of the poles based upon an allowable bending stress of 7500 psi in the aluminum. (b) Determine the minimum required diameter based upon an allowable shear stress of 300 psi.
A steel column ( E = 30 X 103 ksi) that is fixed at the base and free at the top is constructed of a W8 x 35 wide-flange member (sec figure). The column is 9.0 ft long. The force P acting at the top of the column has an eccentricity e = 1.25 in. If P = 40 kips, what is the maximum compressive stress in the column? If the yield stress is 36 ksi and the required factor of safety with respect to yielding is 2.1, what is the allowable load Pallow?
The figure shows an idealized structure consisting of rigid bars ABC And DEF joined by a linearly elastic spring ß between C and D. The structure is also supported by translational elastic support ß at B and rotational elastic support ßRat E. Determine the critical load Pcrfor the structure.
Determine the allowable axial load Pallowfor a steel pipe column that is fixed at the base and free at the top (see figure) for each of the following lengths: L = 2,6 m, 2.8 m, 3.0 m, and 3.2 m. The column has an outside diameter d = 140 mm and wall thickness t = 7 mm, (Assumed = 200 GPa and ( y= 250 MPa.)
Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 500 kN (see figure). The column has an outside diameter d = 200 mm, wall thickness; = 10 mm, E = 200 GPa, and y = 250 MPa.
-11 Determine the maximum permissible length Lmaxfor a steel pipe column that is fixed at the base and free at the top and must support an axial load P = 40 kips (see figure). The column has an outside diameter d = 4.0 in., wall thickness t = 0.226 in., E = 29,000 ksi, and y = 42 ksi.
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.