Liquid X is known to have a lower viscosity and lower surface tension than Liquid Y. Use these facts to predict the result of each experiment in the table below, if you can. experiment predicted outcome OPx will be greater than py Y Liquid X and Liquid Y are each pumped through tubes with an inside diameter of Py OPy will be less than 43.0 mm, and the pressures Py and Py OPy will be equal to py needed to produce a steady flow of 1.9 mL/s are measured. It's impossible to predict whether Py or Py will be greater without more information. O ty will be greater than ty 35.0mL each of Liquid X and Liquid Y are Oly will be less than ty poured through a funnel, and the times Iy Olx will be equal to ty and ty needed to pour each liquid through the funnel are measured. It's impossible to predict whether ly or ly will be greater without more information.

Liquid X is known to have a lower viscosity and lower surface tension than Liquid Y. Use these facts to predict the result of each experiment in the table below, if you can. experiment predicted outcome OPx will be greater than py Y Liquid X and Liquid Y are each pumped through tubes with an inside diameter of Py OPy will be less than 43.0 mm, and the pressures Py and Py OPy will be equal to py needed to produce a steady flow of 1.9 mL/s are measured. It's impossible to predict whether Py or Py will be greater without more information. O ty will be greater than ty 35.0mL each of Liquid X and Liquid Y are Oly will be less than ty poured through a funnel, and the times Iy Olx will be equal to ty and ty needed to pour each liquid through the funnel are measured. It's impossible to predict whether ly or ly will be greater without more information.

Chemistry: Principles and Reactions

8th Edition

ISBN:9781305079373

Author:William L. Masterton, Cecile N. Hurley

Publisher:William L. Masterton, Cecile N. Hurley

Chapter9: Liquids And Solids

Section: Chapter Questions

Problem 79QAP

See similar textbooks

Similar questions

What factor(s) influence the viscosity of a polymer solu-tion? What factor(s) influence the viscosity of a molten poly-mer? What is a polymer glass?
The viscosity of a multigrade motor oil (such as one rated10W-40) is less temperature dependent than the viscosities ofmost substances. These oils contain polymers (long moleculescomposed of repeating units) that coil up at low temperatures butunwind at higher temperatures. Explain how the addition ofthese polymers to the motor oil might make the viscosity lesstemperature dependent than a normal liquid.
which of the following would have the highest viscosity at a temperature and pressure where all are liquid? Rn, He or Ne?
The melting point of mercury at 1 bar is −38.87°C. The density of liquid mercury atthese conditions is 13.69?/??3 and the density of the solid phase is 14.193?/??3. Theassociated heat of fusion is 9.75?/?. Estimate the melting point of mercury under the pressureof 3540???.
What amount of energy is required to change a spherical drop of water with a diameter of 2.00 mm to two smaller spherical drops of equal size? The surface tension, γ , of water at room temperature is 72.0 mJ/m2
5 if the viscosity of Nacl = 664.256 mpa.s viscosity of NaOH= 1.00979 cp viscosity of water= 0.6531 cp what is the viscosity of the mixture if they are mixed together ?
Calculate the viscosity of acetone at a temperature at which the density of the liquid is 784.6 kg/m³, if a Teflon sphere of radius 1.2mm attained a terminal velocity of 14 m/s in the liquid. The density of Teflon is 2.2 g/cc.
Liquid rises to a height of 0.45 mm inside the capillary above the surface of liquid. The height of capillary tube is 10 cm, and the inside volume of capillary tube is 0.72 mm3 and the density of liquid is 0.9 g/cm3. If the angle of contact is 25, calculate the surface tension of liquid?
Polymer PXX has a glass transition temperature of 49°C. Describe the viscoelastic behaviour of the polymer at room temperature and at a temperatureof 55°C
(a) Temperature dependence of the vapor pressure of ethylene log p (mm Hg) = - 834.13 / T + 1.75 log T - 8.375 x 10-3 T + 5.3234 , which gives the temperature dependence of the molar enthalpy of vaporization derive the equation. (b) Calculate the molar enthalpy of evaporation at -103.9 oC, the normal boiling point of ethylene. Note: Use the equation that gives the temperature dependence of ΔHvap= a + bT + cT2+ ….enthalpy.
Saturatad uater vapour at 60c°has iti pressure decrease to ncrease the volume by 10 % Keeping the temperature constant. To what pressure Should be expands.
Sulfur dioxide is produced in enormous amounts for sulfu-ric acid production. It melts at -73°C and boils at -10.°C.Its ΔHfusis° 8.619 kJ/mol and its ΔHvapis °25.73 kJ/mol. The spe-cific heat capacities of the liquid and gas are 0.995 J/gK and0.622 J/gK, respectively. How much heat is required to convert 2.500 kg of solid SO₂ at the melting point to a gas at 60°.C?