LO5 Below is an LC filter circuit, which "smooths" the input source, which is a triangular signal with period T, into an output signal that is sinusoidal, with same period. Assume the peak voltage of v, (1) is 15 V and of v, (t) is 10 V. a) Compute the RMS voltages for v, (t) and v, (1). b) Compute the total power dissipated by the two resistors. (1) 52 v,() 152 LC Filter

LO5 Below is an LC filter circuit, which "smooths" the input source, which is a triangular signal with period T, into an output signal that is sinusoidal, with same period. Assume the peak voltage of v, (1) is 15 V and of v, (t) is 10 V. a) Compute the RMS voltages for v, (t) and v, (1). b) Compute the total power dissipated by the two resistors. (1) 52 v,() 152 LC Filter

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A coil of inductance 120 mH and resistance 150 ohm is connected in parallel with a variable capacitor across a 20V, 4 kHz supply. Determine for the condition when the supply current is a minimum, (a) the capacitance of the capacitor, (b) the dynamic resistance, (c) the supply current, (d) the Q-factor, (e) the bandwidth, (f) the upper and lower −3 dB frequencies, and (g) the value of the circuit impedance at the −3 dB frequencies.
An Armstrong modulator is used to generate FM which is suitable for FM broadcasting.You are given input of narrowband FM signal with carrier frequency fc1 = 27 MHz anda frequency deviation Δf1= 17 kHz. Assume that the frequency multiplier with n = 3 andlocal oscillator frequency of 80 MHz. Calculate the output of the carrier frequency andfrequency deviation if additive frequency is selected by mixer. Explain your obtainedanswer.
A superheterodyne receiver is to tune the range 88.1MHz to 107.1MHz. The RF circuit inductance is 1μH. Low-side injection is used.a. Calculate the minimum capacitance of the variable capacitor in the RF circuitb. Calculate the RF circuit capacitance tuning ratio c. If the receiver has a single converter stage and IF of 800kHz, calculate the capacitance tuning ratio of the local oscillator d. If the maximum capacitance of the variable capacitor of the local oscillator is 0.2pF, calculate the minimum capacitance e. If the receiver has a single converter stage and IF of 800kHz, calculate the image frequency of 103.7MHzf. Calculate the IFRR (in dB) of (e) if Q of the preselector is 50 g. To increase the IFRR of (e) to 40dB, double conversion is used. What must be the frequency of the 1st IF?
When the ltspice simulation of the circuit shown in the figure is performed, the output voltage (Vout) is obtained as given in which of the figures below? NOTE-1: Vcc = 12 V, RC = 2.2 kΩ, RB = 15 kΩ, RE = 180 Ω and C1 = 1 μF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.
A 8-stage impulse voltage generator is connected to a test object of load capacitance of 5000pF with wave front resistance equal to 700 Ω. If the wave tail and wave front times of the impulse wave are 50 μs and 1500 ns respectively. Calculate (i) wave tail resistance value and (ii) the capacitance of the impulse generator?
Electronic Since k = 0.35x10^3, VGSQ = 6.2 V, VGS(Th) = 2.4 V, RF = 100 MΩ, RG = 10 MΩ, RD = 7.6 kΩ, RS = 2.2 kΩ and RL = 21 kΩ in the circuit in the figure, the output voltage In which option is the amplitude value (Vout) given correctly? NOTE-1: E-MOSFET output impedance is rd = 70 kΩ and should be taken into account in calculations. NOTE-2: Capacitors are of negligible size at mid-band frequency. NOTE-3: It is within the 5 kHz mid-band frequency.
Suppose Rc=10 k, Rb=1k, Vcc=4V, Vi =5V, and β= 200. Find Vbe, Vce, Ic, and the region of operation.
A 25 V, 2.5 kHz supply is connected to a network comprising a variable capacitor in parallel with a coil of resistance 250 ohm and inductance 80 mH. Determine for the condi tion when the supply current is a minimum (a) the capacitance of the capacitor, (b) the dynamic resistance, (c) the supply current, (d) the Q-factor, (e) the bandwidth, (f ) the upper and lower half-power frequencies and (g) the value of the circuit impedance at the −3 dB frequencies.
1. For an electronic device operating at a temperature of 17°C with a bandwidth of 10 kHz, determine:a. ThermalnoisepowerinwattsanddBm.b. Rmsnoisevoltagefora100Ωinternalresistance. 2. Two resistors, 20 kΩ and 50 kΩ are at ambient temperature. Calculate for a bandwidth equal to 100 kHz, the thermal noise voltage for the tworesistors connected in parallel.
What can you conclude from the three types of AM (DSBFC,DSBSC and SBSC)? Explain your answer properly.
ı just need the fınal answer Since Vcc = 20 V, RS = 3 kΩ, RB = 380 kΩ, RC = 1.2 kΩ, RE = 2.2 kΩ, RL = 911 Ω and β = 90 in the circuit in the figure, find the value of the output voltage (Vo). NOTE-1: It is within the 1 kHz mid-band frequency and the capacitors are negligible at this frequency. NOTE-2: The output impedance (r0) of the transistor will be neglected. a. 64,14 mV b. 83,88 mV c. 93,75 mV d. 74,01 mV e. 103,62 mV f. 24,67 mV g. 34,54 mV h. 49,34 mV
When Itspice simulation of the circuit shown in the figure is performed, which of the following figures is the output representation (Vout) as given? NOTE-1: Vcc = 12 V, RO = 2.2 kO, RB 15S kO, RE 180 0 and C11 uF. NOTE-2: For the input voltage Vin, the DC offset voltage is 1.6 V, while the applied sinusoidal signal has a amplitude of 10 mV and a frequency of 10 kHz.