load ic 本TI 本「本T3 V load + b R The circuit given above is directly connected to our current low voltage network. Calculate the C constant of the thyristor current according to the values given below. E=100V R= 4 ohm L=75mH alfa= 90 degree A) -9 B) -18 C) -41 D) -32 E) -25

load ic 本TI 本「本T3 V load + b R The circuit given above is directly connected to our current low voltage network. Calculate the C constant of the thyristor current according to the values given below. E=100V R= 4 ohm L=75mH alfa= 90 degree A) -9 B) -18 C) -41 D) -32 E) -25

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: www.nitropdf.com Engineering Circuit Analysis 8* Edition Chapter Four Exercise Solutions 58. One…

A: Design a circuit to 1.make the controlling quantity 8v1 i.e depends on a nodal voltage. 2..make the…

Q: A 30, 45 kV is supplied to converter which is used in a HVDC transmission system. Each thyristor has…

A: Given data is shown below. Vf=45kVVbm=1740V△ID=42.5mAη=77%=0.77

Q: A3Ø, 30 kV is supplied to converter which is used In a HVDC transmission system. Each thyristor has…

Q: A three-phase,50-Hz, 480-V system supplies the following loads: 1. A six-pole, 50-Hz, 460-hp,…

Q: Calculate the current I for the network of the circuit below. 20V, I, = 1 mA Z0° R,$ 2 k2 V,R2 5 kfN…

Q: Solar water heating is less efficient than PV systems for exploiting solar energy. True False

A: Given Solar water heater is less efficient then pv cell True or false

Q: R = 30 N R = 35 N 3 OV, = 10 volts R = 7 N R = 5 N R = 10 N R = 18 N R = 5 N OVs = 200 volts 6 5 Use…

Q: Question 2: 1. Safety Precautions: a. Based on the Apartment's plan distribute the electrical…

A: Detailed solution of the question is given below Please find the attachments

Q: a) If the electrical power required for a house is assumed to be 5kW, the requirement of 1500xy…

A: Given data: Output power requirement: 5 kW Net water head: 190 m Penstock efficiency: 91% Turbine…

Q: 11. A 50 kVA, 2200/110 V transformer when tested gave the following results : O. test (L.V. side):…

Q: A 3Ø, 35 kV is supplied to converter which is used in a HVDC transmission system. Each thyristor has…

A: Given : Vs=35kVVbm=1560 V∆Ib=35mAη=79%∆Qmax=29μC

Q: R, R, :0 4の R, R. の Fig. Equivalent Circuit of IM Three phase, two pole, 60 Hz IM is obtained to be…

A: Given data: Pin=15.7 kWR1=0.2 ΩI2=22.6 AP=2f=60 HzNr=3502 rpm

Q: Computation: A house has the following specifications for a circuit. Determine the size of the…

A: We have Given; A house has the following specifications for a circuit. Determine the size of the…

Q: 11.a. In dwelling units, motels, hotels, and other occupancies such as dormitories, nursing homes,…

A: When feeder current exceeds 200 A then the demand factor of 70 % applied to excess current Suppose…

Q: A computer lab of 20 m * 10 m consists of following loads, 1.Light points 20 nos (45 W) 2.Fan points…

A: We have been given an computer lab with, Area = 20 m * 10 m The load of this computer lab is,…

Q: Q3)-- Design an Ayrston shunt to provide an ammeter with current ranges of 11mA, 26mA And 101mA, Ad…

A: The Aryston shunt method is used to extend the meter reading to large range by adding shunt…

Q: Q.2: For the network of figure 2, determine: a-calculate r, b- calculate Zi and Zo (using r. model…

A: Given:Vcc= 16VR1=39kΩR2=4.7kΩRC=3.9kΩRE=1.2kΩ The given circuit is a voltage divider bias circuit…

Q: Procedure 1. Using the DC circuit trainer, connect the circuit Shown in Fig. (4), take Vr =10V, and…

A: The solution can be achieved as follows.

Q: C1 a V2 Vi(t)(+ V;(t) gv, L, R, v, (t) = 10 cos(2n · 103t) V, R, = 100 N, L, = 20 mH, C, = 1 µF,g =…

Q: Procedure 1. Using the multi-sim, Connect the circuit shown below: a b R3 820 1002 R2 R4 5 V d 2.…

Q: A 15 KVA, 440/230 V, 50 Hz, transtormer gave the following test results: Open Circuit (LV side) 250…

A: The open and short circuit parameters of the transformer are given . Find the transformer…

Q: (c) Using a circuit analysis technique of your choosing, calculate the mesh currents and power…

A: In loop 1, applying Kirchoff,s voltage law. 955V-100I1+2(I1-I2)+12.44 V=0967.44 -100I1+2(I1-I2)=0

Q: Estimate the cell temperature and power delivered by a 100-watt PV module with the following…

A: (a): The cell temperature of the module is: Tcell=Tair+NOCT - 2080 STcell=25 +…

Q: Q2: Draw the single line diagram of a substation having the following equipments: (1) Incoming…

A: To design the High voltage substaion, ultra fast protecting device should be used. Isolation between…

Q: A single family dwelling with a floor area of 80 square meters has the following receptacles and…

Q: A substation of 440kV, 5000A located at Al-Qabil, is feeding the whole of the Al-Alaya loads…

A: for a transformer , primary voltagesecondary voltage = primary turnssecondary turns given primary…

Q: statement 1. Flexibility of the circuit – means that the installation can accommodate all probable…

A: Flexibility of circuit A conductor pattern built on a flexible film that serves as a dielectric base…

Q: The equipment required for the apartment are listed below: No. Equipment Description Equipment…

A: To find total consumption , power consumption of single equipment is multiplied with required…

Q: 39 ' Si 10 V 10Ω Si Figure 4 Determine the current I using the approximate/practical equivalent…

Q: Which of the fallowing is a PV system designed to offset some of the customer's purchased utility…

A: To find which pv system used by customer in emergency of power cut :

Q: Use KVL, KCL methods to solve for the required parameters. Write the summary of your answer in the…

A: We need to find out the voltage across 50 ohm resistor and voltage across 80 ohm resistor for the…

Q: Renewable Energy Systems Homework 2 One type of PV module consists of 72 cells and the size of…

A: In this question first find the output of solar cell under standard test condition . Find the power…

Q: Match the sentence, word, or equation with the best choice from the list given: - [V/A] Loop Units…

Q: A house has the following specifications for a circuit. Determine the size of the circuit breaker,…

A: The Selection of the circuit breaker and wire should be mandatory while wiring a house since it make…

Q: 40 Which of the following is a PV system designed to offset some of the customer's purchased utility…

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Practice Problem In the circuit shown, calculate the nodal voltages V,V & V 2A Va V1 V3 ww 20 2 10 2…

A: Lets use the concept of nodal analysis to find the node voltages in this question.

Q: Q 2. In a series-parallel circuit shown in Fig.2. the parallel branches A, B, and C are in Series…

A: ZA=2ΩZB=(3+j4)ΩZC=(2+j2)ΩZD=(1+j1)Ω

Q: University of Basrah College of Engineering Department of Computer Engineering First Year Electrical…

A: Before getting in to the actual question lets get in to some basics Thevenin's Theorem: Thevenin's…

Q: ssuming a 12 V dc supply is connected to the circuit as shown, calculate: I, ls, I2, ls, V1, V2 and…

Q: The specification of a solar PV system is given below: Number of PV modules: 4 Number of PV cells in…

A: The specification of a solar PV system is given below: Number of PV modules: 4 Number of PV cells in…

Q: A 2-wire d.c. distributor AB is 600meters long is loaded as under: Distance from A (meters) 150 300…

A: The circuit diagram for a two-wire d.c. distributor system is shown below:

Q: a) A 380V, 7.5kW electric water pump of power factor 0.8 lagging and efficiency of 85% will be wired…

A: An MCCB is nothing but a circuit breaker used as a protective device for over-current protection.…

Q: 24. A 3 phase, 4 – wire, 400 V symmetrical system supplies a Y – connected load having the following…

Q: A small supermarket 20 m long by 15 m wide is to be illuminated to a level of 600 lx by 2400 mm 125…

A: The illuminance of a light source or bulb is measured in terms of "Lux". The luminance, whereas, is…

Q: 10Ix Do.9 ma 3 k2 16 V bọ 2kN Ix

Q: Q.2: For the network of figure 2, determine: a-calculate r, b- calculate Zi and Zo (using r, model…

A: Relation between re and hi model;β re=hiβ=hf

Q: A natural waterfalls, 50 meters high, constantly discharges 1.3m3 per second. A mini hydroelectric…

A: Given that h=50 mr=1.3 m3/sηm=90%ηT=70% Although for given power system , formula for electric…

Q: + Vi - - Vz + R, = 1.2 kn A R, = 2.2 kn 20 V V3 3.3 kn 10 V FIG. 14.1 (b) Using branch-current…

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

load
iTI
ic
E
load
L
"bn
ib
The circuit given above is directly connected to our current low voltage network.
Calculate the C constant of the thyristor current according to the values given below.
E=100V
R= 4 ohm
L=75mH
alfa= 90 degree
A) -9
B) -18 C) -41 D) -32 E) -25

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a 24v zener regulated power supply circuit that will power a 500 ohms load with 1A of of current. Determine the power rating of both bleeding resistor and load resistor. Note the computed power dissipation differ from the required power rating of the device.
Compute the percent difference between the results of the measured and computed values of currents and voltages. Measured value Vcd = -6.71 V Icd = -0.24 A Vbf = 17.88 V Ibf = 0.38 A Computed value Vbf = 15.877 V Ibf = 0.283 A Vcg = -7.368 V Icg = -0.2916 A show complete solution
answer the following questions using the attached picture. (c) To measure the current flow though R1 and the voltage onR5, how should we connect the ammeter and voltmeter?Draw a circuit diagram showing your answer. (d) What is the ideal impedance of1). an ammeter?2). a voltmeter?
Determine mesh currents. Show step by step solution thank youu.
a) A 380V, 7.5kW electric water pump of power factor 0.8 lagging and efficiency of 85% will be wired by an armoured XLPE insulated copper cable. The circuit will be run on cable tray with three other similar circuits at an ambient temperature of 40℃. MCCB will be used as the overcurrent protective device for the circuit. The estimated length of the circuit for the machine is 50m. i) Determine the minimum rating of MCCB for the circuit, available MCCB rating are 25A, 30A, 40A, 50A ii) Determine the minimum cable size of the circuit if the allowable voltage drop of the circuit is 1.5% of the nominal supply voltage?
Topic: Direct Current Circuit which contains Open and Short Circuit, Series and Parallel Circuit, Current Divider Principle, Voltage Divider Prinicple, and Delta-Wyne Connection. Determine the value of VT and I. Note: DRAW THE DIAGRAM
Determine the mesh current IX shown in the figure below.Please provide a CLEAR and COMPLETE solution
Lrocedure A- Kirchhoff's voltage law: The circuit in Figure 2 will be used o test the valdity of Kirchhoffs voltage law, Figure (2) Construct the circuit as shown in the figure (2). Measure the power supply output voltage and the potential drops across each of the thrae resistors. Record these measurements in your lab notebook as in the following table: University of Ti-Qar/ Departmnt of Elctricl aad Fectronlc Enginearing / Prepared by M 5¢ Al Karvem Soes 1+ Stage: Fundamentals of Flectrical Engineering | Lob 3 - Kirchhoff's Laws. 201520, Table 1; data collected for testing the validity of Kirchhot?s voltage law. 3)From your experimental data (table 2), calculate the total current into the node point P. Now calculate the total current out of the node point P along with its uncertainty. Does the current into the node agree with the current out of the node within experimental uncertainty?
In the circuit given in the figure | VBE | Since = 0.7V, R1 = 2.66Kohm, R2 = 11.73Kohm, RC = 0.79Kohm, RE = 2.36Kohm, VCC = 14.00V, Beta = 115.00, calculate the IC current by full analysis. When making your transactions, 2 steps will be taken after the point. Select the closest option according to +/- 10% margin of error. There is only one correct answer to the question.
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Flux Luman output per 200 W lamp Luman output per 500 W lamp Number of 500W lamps required Number of 220W lamps required Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
5: Which one of the following energy resources need stored water for its operation? a. Biomass b. Hydro power c. Waves d. Tidal 6: How shunt leakage current is represented in an equivalent circuit of photovoltaic module? a. ISH b. IDH c. ISI d. ILH
Objectives: Voltage drop measurements using resistors connected in series. The relationship between resistance value and voltage drop (Kirchhoff’s Second Law) Circuit components: 1 Plug-in board, DIN A4 576 74 1 STE resistor, 100 W, 2 W, 5% 577 32 1 STE resistor, 150 W, 2 W, 5% 577 34 1 STE resistor, 1 kW, 2 W, 5% 577 44 Power Supply: 1 AC/DC stabilizer 726 88 Connectors: 3 Pairs of connecting leads, red/blue, 50 cm 501 45 1 Set of 10 bridging plugs 501 48 Measurement Instruments: 1 Voltmeter, 10 V DC 1 Amperemeter, 10 mA DC Measuring the voltage drop across resistors…