long piece of wire is bent into a rectangular loop and placed on a table top in the horizontal plane. A very long straight piece of wire, placed as shown in the diagram below has a current I = 4a - 2bt? flowing in the direction indicated. The wire is at a distan 1 = 2.50 cm from the left side of the rectangular loop. What are the magnitude and direction of the induced emf in the loop at t = 1.32 s? Here a = 13.2 A, b = 1.40 A/s?, e = 0.500 m, and w = 0.250 m. nagnitude irection ---Select--

long piece of wire is bent into a rectangular loop and placed on a table top in the horizontal plane. A very long straight piece of wire, placed as shown in the diagram below has a current I = 4a - 2bt? flowing in the direction indicated. The wire is at a distan 1 = 2.50 cm from the left side of the rectangular loop. What are the magnitude and direction of the induced emf in the loop at t = 1.32 s? Here a = 13.2 A, b = 1.40 A/s?, e = 0.500 m, and w = 0.250 m. nagnitude irection ---Select--

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter32: Faraday’s Law Of Induction

Section: Chapter Questions

Problem 45PQ

See similar textbooks

Similar questions

The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
Design a current loop that, when rotated in a uniform magnetic field of strength 0.10 T, will produce an emf =0 sin t. where 0=110V and 0=110V .
The normal to tt plane of a single-turn conducting loop is directed at an angle to a spatially uniform magnetic field B. It has a fixed area and orientation relative to the magnetic fleck Show that the emf induced In the loop is given by i = (dB/dt)(Acos),where A is the area of the loop.
A flat, square coil of 20 turns that has sides of length 15.0 cm is rotating in a magnetic field of strength 0.050 T. If tlie maximum emf produced in die coil is 30.0 mV, what is the angular velocity of the coil?
A long piece of wire is bent into a rectangular loop and placed on a table top in the horizontal plane. A very long straight piece of wire, placed as shown in the diagram below has a current I = a − bt2 flowing in the direction indicated. The wire is at a distance of d = 2.50 cm from the left side of the rectangular loop. What are the magnitude and direction of the induced emf in the loop at t = 1.30 s? Here a = 17.4 A, b = 1.78 A/s2, ℓ = 0.500 m, and w = 0.250 m. magnitude direction Additional Materials Tutorial
A long solenoid of radius r = 1.60 cm is wound with 4.00 ✕ 103 turns/m and carries a current that changes at the rate of 23.5 A/s as in the following figure. What is the magnitude of the emf induced in the square conducting loop surrounding the center of the solenoid?mV An illustration of a solenoid of radius r, which is a horizontal cylinder with a wire wound around its length into a coil. If viewed from the left end of the cylinder, the current I flows clockwise through the coil. A square loop of wire is positioned around the center of the cylinder, where the plane of the square is perpendicular to the length of the cylinder.
A long solenoid of radius r = 1.85 cm is wound with 4.50 ✕ 103 turns/m and carries a current that changes at the rate of 31.0 A/s as in the following figure. What is the magnitude of the emf induced in the square conducting loop surrounding the center of the solenoid?
In the diagram below, a rectangular 40 loop coil of width w=10 cm and length l= 14 cm begins in a region with no electric field and then moves to be completely inside a region of uniform B=1.3 T coming out of the page. If this process occurs over a time period of 3 s, what is the magnitude of the induced emf in the coil of wire? a) 0 V b) 0.0061 V c) 0.243 V
The flexible loop in the figure below has a radius of 13 cm and is in a magnetic field of strength 0.14 T. The loop is grasped at points A and B and stretched until its area is nearly zero. If it takes 0.23 s to close the loop, what is the magnitude of the average induced emf (in mV) in it during this time?
An L = 47.0 ncm wire is moving to the right at a speed of v = 6.50 m/s across two parallel wire rails that are connected on the left side, as shown in the figure. The whole apparatus is immersed in a uniform magnetic field that has a magnitude of B = 0.910 T and is directed into the screen. What is the emf induced in the wire? If the moving wire and the rails have a combined total resistance of 1.15 Ohms, what applied force would be required to keep the wire moving at the given velocity? Assume that there is no friction between the moving wire and the rails.
A solenoid of length 3.70 cm and diameter 0.760 cm is wound with 272 turns per centimeter. A) If the current in the solenoid is decreasing at a rate of 38.8 A/s, what is the induced emf in one of the windings? B) If the current in the solenoid is decreasing at a rate of 38.8 A/s, what is the induced emf in the entire solenoid?
In the figure below, the conducting loop has fallen a short distance and is now falling at a constant velocity, vterminal. The loop has sides of length s=0.50 m, mass 30.0 g, and resistance R=1.00 Ω. If B=7.50 T and is directed into the page, answer the following question: What is the magnitude of the force pulling down on this loop and according to Lenz’s Law, in which direction will an induced current in the loop travel? Make sure to show how you know and all your work.